Search results

Nobody had experience with these batteries???? :cry:

Hi all I have a Makita 6317 cordless drill driver with two Ni-cd 2.0Ah batteries; the drill driver is just fine, the life battery is quite short. I would like to buy an extra battery. Would you recommend a 2.6Ah Ni-mh replacement (not original) battery? The cost is 30-40% less of a brend new...

thanks a lot..... what about the 90° square made by Dewalt for its rail? is it accurate?

Hi there I own a Festool TS55 plunge saw with 1.4 mt rail (just bought a week ago) with two clamps. I would like to buy some extra accessories, but I have some doubts..... First of all, I'm sure I need an extra rail; I have an FS800/2 rail (along with the OF1010) but I want to buy a longer one...

here is mine. few planes are missing....

I had the same "problem" with my 1/2" AI chisel; the difference between the two sides was quite small. Indeed also my LN 1/2" has the same!! Actually I don't care a lot......very good chisels BTW

many thanks for the replays. actually I have some crosscutting sleds, which are quite accurate for work up to 80 cm width and the scheppach sliding carriage seems expensive.....

I own both planes and they are a pleasure to use, easy to adjust. The left version is very handy if you also pull the plane (thanks Rob!) but obviously you can start buying just the right version. The skewed blade really makes the difference over the 778, but the plane has a lot of nice features.

Hi all I own a scheppach TS2500ci bench saw and I'm quite happy with it; the saw has table lenght and width extensions. Would you consider buying a sliding table carriage for this saw? if so, the 1400 mm is fine?

here's mine......some planes/saws are missing.....

ohh! I really don't need them......ugly.....cheap.....useless..... ohh! I really don't need them......ugly.....cheap.....useless..... ohh! I really don't need them......ugly.....cheap.....useless..... ohh! I really don't need them......ugly.....cheap.....useless..... ohh! I really don't need...

On my block planes I have different bevel angles. The LV has a final angle of 30° (25° + 5°); is the plane I use often The LN 102 has a 30°+2° angle The stanley 60 1/2 has an Hock A2 blade with a 25° bevel angle and a back bevel of 5° (for an effective cutting angle of 37°)

thanks for the replay I have 3 routers and I'm very curious about jour jig........ Woody magazines in Italy? Just one......very jung (only two numbers) "legno-lab"......

Hi all I would like to try this type of joint for some frame I have to made. Which one do you recommend? The Kreg K3 seems not available at Axminster (I'm making an order for other stuff...). It's the R3 fine? do I really need a face clamp? What do you think about the Axminster jig...

Thanks, Matthew! Are all the AI cabinetmakers bevel edge chisels on sale from you the new MK2 version? I just saw that on the site it says, for single chisel and set of six, only "Ashley Iles Bevel Edged Cabinetmakers Chisel"...... http://www.workshopheaven.com/eStore/cg ... ME:Chisels...

Excellent review Paul! I had the chance to use both the versions of these fantastic planes. I totally agree with custard regarding the two grub screws, that in these planes are really useful, especially when you need to set the blade and align it to the side of the plane (forget the paper...

Hi all I'm trying to improve the fence of my Scheppach TS2500ci bench saw and make some zero-clearance inserts for my mitre and bench saws. In you opinion it is fine to use some 6 mm thick UHMW for the purpose? Axminster has it.... May I use it also for mitre slot bars (for the crosscutting sled)?

OK guys, I will give up with my bad idea! thanks for the advices. I asked for the scheppach special cutter to my local dealer; it is quite expensive (250€). It is possible to find it for less? If so, where? There are other adjustable groover cutters similar to the scheppach one that might fit...

Hi all I was following with great interest the recent discussion on dado blades and bench saws. Actually I have a TS2500ci and I was just "making" a sort of dado blade using three CMT grooving saw blades (cat. numb. 240.050.07M) and two custom-made reduction rings (made with C4 steel on an...

My n°10 (I don't have a 10 1/2) is the less-used plane in my shop. I prefer a n°5 or a large shoulder plane when needed. Indeed it's a beautiful plane 8)