Built in Cabinet Design Advice seeked.

UKworkshop.co.uk

Help Support UKworkshop.co.uk:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

wizer

Established Member
Joined
3 Mar 2005
Messages
15,589
Reaction score
1
Hi

I am fiddling around in Sketchup, trying to design a built in cabinet for my conservatory. As a newbie I have never built anything like that. I wondered if anyone could point me in the direction of any online information for built in cabinets?


This is what I have so far:

cabinet1.jpg

cabinet2.jpg

http://www.wizer.co.uk/conscab.skp

The first picture shows the back of the cabinet. Picture shows the front with a mock-up of 3 doors.

I will probably use m/t's for the frame joints. My main query atm is the floor of the cabinet and how to make it flush with the door opening.[/list]
 
If it's floor standing you could use a plinth set back 30-50mm's or so. That would give you an effect similar to fitted kitchens if you use overlaid doors.
If you want to use inset doors, ie doors set into a frame, then make a face frame for the cabinet and arrange it so that the face frame is flush with the base of the cabinet, and underhangs if the frame rail is wider that the thickness of the base material (which it usually is, thus making the plinth a necessity)
John
 
Thanks John, I hadn't thought of a plinth. That will give me a few ideas to play with.
 
I canna help thinkin maybe this might help..

http://www.taunton.com/store/pages/070534.asp

if its anything like the others in the series, it'll cover every major technique (and quite a few others too) involved in cabinet making, explaining how to go about the making of each in a variety of different ways; enough to please Normite and knuckle-dragger alike...
 
thanks guys, one for the xmas list i think! :wink:
 
here's the new improved version using the plinth idea. Another project for the list...


conscab2.jpg
 
For my twopennorth on design - difficult to read the numbers but i think I can make out that it is 2520mm long with each door being 840mm wide.

Might look better and not require so much clearance room or put so much strain on the hinges if you made it 6 doors each c 420 wide.

Just a thought.

Cheers

Tim
 
very good point tim. The middle opening is to house a small Wine (Stella) Fridge. So this is what I have based the door openings on. I did not think of clearance. Have to have a rethink.
 
Wizer if you are putting a fridge in there have you thought about venting the cupboard, fridges produce a fair amount of heat.

Bean
 
yes I have thought about it bean, not sure how I will tackle it. Maybe some routered vent holes in the top, or a mesh section. Failing that I could Have the end of the cabinet vented, however this won't be efficient on air flow. Put a fan in..?
 
Latest update with the double doors. Need to take some more measurements tonight for the fridge in the middle.

conscab3.jpg


The top will prolly be either maple veneered worktop (if they make that). or just mdf painted white. It just going to have plant pots and ornaments on it. In the drawing I have left the colour of the carcass green for contrast but it will all be white painted mdf. The doors will just be rounded over all round (dont know how to do that in sketchup!)
 
Wizer
I have just checked around an inbuilt fridge I have, there is a inlet in the plinth a good space behind (cannot get in with a tape). There is an open space to the top of the cabinet, but I think if you could disguise a vent on the top of the cabinet you would get away with it without a problem.
In fact given the size of the cabinet a vent at the top may not be needed.

Bean
 

Latest posts

Back
Top