Lots of cladding - which nail gun/nails

UKworkshop.co.uk

Help Support UKworkshop.co.uk:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

ben2

Established Member
Joined
24 Feb 2010
Messages
50
Reaction score
2
Hi

I have around 500lm of cladding to install. Is 12 mm thick, going onto softwood joists.

Ideally I was looking to get a pneumatic nailer like Axminster:

http://www.axminster.co.uk/axminster-ai ... ler-953415

However I want to use stainless T nails 30 mm long or so, and Axminster don't sell them...

So are there any other combination I should be looking at or does anyone know where I can get 16g stainless T nails.

Thanks in advance

Mark
 
What sort of cladding where will it be? Brad nails like this are not really very good for external cladding for instance, they don't really have the holding power.
 
When this cladding is finished, will you need a frame nailer again?
If you're not a chippie type person, Possibly the finish or brad nailer would be more useful in the workshop, later.
I think frame nails start at 50mm.
Rodders
 
Hi

Its internal cladding - I haven't decided on whether I will paint or varnish the surface, I want something that will not damage the surface of the wood too much, so less prep work.

It 12 mm cladding, going into a softwood frame - 50mm nails sound like overkill?

What frame nailer would you go for and where to get stainless nails?

Thanks

Mark
 
Not structural then, just for aesthetics? If so then an 18g brad nailer is your best bet, very cheap (aldi have one for £20 next week), will take nails from 16mm up to 50mm usually (My lidl one does, and staples too) and they are very discrete.
 
You won't need stainless nails for internal work, everyone rightly assumed it was external as it normally is.


Sent from my iPhone using Tapatalk
 
ben2":jtcd6gpv said:
Hi

Its internal cladding - I haven't decided on whether I will paint or varnish the surface, I want something that will not damage the surface of the wood too much, so less prep work.

It 12 mm cladding, going into a softwood frame - 50mm nails sound like overkill?

What frame nailer would you go for and where to get stainless nails?

Thanks

Mark
I'm no expert on nail guns, but I would first look at the axminster model you highlighted in you're OP.
I've bought stuff from them over the years and found them pretty reliable to help in anyway possible.
If its internal cladding, why would you need stainless nails for anyway?
Some here,- http://www.screwfix.com/c/screws-nails- ... /cat840034
galvanised is good for in or outside.
Rodders
And, advise-please-nail-guns-and-nails-t60127.html
 
Hi

Thanks for the replies.

I wanted stainless to avoid any issues with rusting and paint. The internal cladding is going in a (very) well summerhouse which will only be heated when in use. I am worried about condensation causing rust over time.

The original nail gun recommendation was from Axy and I would have bought immediately if they offered stainless or galvanised nails to suit, but they don't. I hadn't realised about SS nails pushing out over the years - thanks for the links Rodders.

I think I'll buy the Axy nail gun and whizz down to Screwfix and open a couple of boxes to see which nails fit.

Thanks

Mark
 
I assume you already have a compressor? If not it might be cheaper to go for a battery option. I've got the Ryobi 18g one and it's really good. I used it for loads of cladding work over the summer and it didn't miss a beat. I paid around £100 for it but I've seen them for significantly more. I already had batteries though so that wasn't a cost.


Sent from my iPhone using Tapatalk
 
For me Senco are the kings of the nail gun range. They have every kind of nail gun there is ranging from DIY models to industrial standard models for all day every day use. They do stainless and galv nails in all manner of sizes and are very competitively priced. The axminster one you are looking at would fall into their semi pro range which is Senco S200BN SEMIPRO Air Nailer 18 Gauge.
For my money Senco is more value for money and is about the same price bracket as the other one.
 
Phil Walker@Appleby":31ye1ctx said:
For me Senco are the kings of the nail gun range. They have every kind of nail gun there is ranging from DIY models to industrial standard models for all day every day use. They do stainless and galv nails in all manner of sizes and are very competitively priced. The axminster one you are looking at would fall into their semi pro range which is Senco S200BN SEMIPRO Air Nailer 18 Gauge.
For my money Senco is more value for money and is about the same price bracket as the other one.

Little bit biased if you sell said item though :wink:
 
clk230":299cizjq said:
Phil Walker@Appleby":299cizjq said:
For me Senco are the kings of the nail gun range. They have every kind of nail gun there is ranging from DIY models to industrial standard models for all day every day use. They do stainless and galv nails in all manner of sizes and are very competitively priced. The axminster one you are looking at would fall into their semi pro range which is Senco S200BN SEMIPRO Air Nailer 18 Gauge.
For my money Senco is more value for money and is about the same price bracket as the other one.

Little bit biased if you sell said item though :wink:
lol! I know what your saying but I was a site joiner/carpenter for 10 years before I'm doing what I do now and it was me that got them on board. Trust me they are the best at what they do because they concentrate on just the nail guns and screw guns they get really good at it, instead of doing a bit of everything.
 
tim co do stainless steel 38mm 16 gauge that fit paslode nailer for £23.50 50mm nails are a bit more not sure of the price hope this helps
 

Latest posts

Back
Top