Search results

Try Builder Depot, New Southgate http://www.builderdepot.co.uk/wbp-plywood-birch-through-out-bb-cp-12mm-x-1220mm-x-2440mm.html http://www.builderdepot.co.uk/wbp-plywood-birch-through-out-bb-cp-18mm-x-1220mm-x-2440mm.html Brian

If you think you might use these fairly often it might be worth getting a set of these http://www.ebay.co.uk/itm/TREND-SNAPPY- ... 5b01288de6 Brian

The last thing you should do with yew wood is burn it on an open fire - all parts of it are toxic and give off poisonous gases. Be warned!! Brian

http://woodgears.ca/table_saw/fence_micro.html I know it's not cheap and only works on cast iron tops but it sure is accurate. Brian

That would certainly do the job. Are CEF just trade? Do they sell such things in small quantities? Any idea of price? Brian

No, I never did. Made them the old fashioned way out of beech. Brian

Here's a link to an article from Fine Woodworking http://www.finewoodworking.com/fwnpdffree/humidor.pdf or go to their website and type humidor in the search box Brian

Coincidentally scraper sharpening was in the last blog from Matthias Wandel at Woodgears http://woodgears.ca/scraper/index.html#v Brian

I use of one of these http://www.axminster.co.uk/numatic-numatic-nvd750-workshop-vacuum-extractor-prod782721/ It's linked to one of these kits plus a few extras http://www.axminster.co.uk/axminster-63mm-dust-extraction-kit-prod21901/ I can control the extractor from anywhere in the workshop...

I bought one of these http://www.ffx.co.uk/tools/product/Makita%20Bo4555%202%200088381081719%20Bo4555%20240V%20Palm%20Sander%20Clamp%20%20Hook%20And%20Loop and have been very satisfied. I chose the hook and loop system so I could use it with these...

Thanks for that. I knew I had seen an alternative method that may avoid bending the motor spindle. Fortunately, I have an airline so shall be experimenting with the turbine effect!! Brian

I think that was the warning issued earlier. It is extremely dangerous to use the wrong collet. Firstly a 1/2" cutter won't fit a 12mm collet and a 1/4" won't go in a 6mm one but if you reverse the sizes, you'll never do them up tightly enough. I've long planned to make this change with my TRA...

The collet system on the larger Triton router is perhaps its only weakness. Ray Girling gives a good comparison between the two and it is clear that the two are not interchangeable. http://www.raygirling.com/triton14.htm The larger machine is described as having a Hitachi style system so it...

Rutlands do a good price for a couple of the clamps mentioned above http://www.rutlands.co.uk/workshop-&-power-tool-accessories/pocket-hole-&-dowel-jigs/pocket-hole---clamps/38518/pocket-hole-clamps Brian

I use one of these for my sander and it works very well http://www.axminster.co.uk/numatic-numa ... rod782721/ Brian

You can cut them into 9" sections with an angle grinder, reverse alternate strips so the teeth point in the opposite direction, put say 6 of them together and bind the ends with insulating tape. You can use this as a flexible scraper for removing old paint or varnish in preparatory work. Because...

The website invites customer enquiries and offers free samples. Why not get some and see what it will do? http://ecodek.co.uk/?seed=ecodec&gclid=CIKcjIbclrECFU6JfAodEBvP5A Brian

If the extension is even a little bit out in machining it will introduce a huge wobble in such a large bit, even at 10,000rpm. Potentially very dangerous, not to mention lethal. Is the bit one that cuts horizontally or vertically? Re the hole: Is it that you don't have an insert disc the right...

First thing to check is that the motor is actually working. Remove the blade including the inner and outer flanges fitted either side of the blade. Switch on briefly to check that the arbor rotates. If it doesn't you should check the brushes to see if they are in good condition. Use your manual...