Search results

Thanks all for the kind words.

Now that's a thinking man =D>

You're not meant to tap the ash off a Cigar (good ones anyway) putting them on or in an ash tray can knock the ash off if it slides one of two ways, rolls or gets knocked picking up or setting down. A rest allows the smoker to put a cigar down without risk of knocking the ash off :) At least...

Turned and carved these two guys up last week. Both in Amboyna. Made a welcome change from Body jewellery day-in-day-out http://southshoreadornments.com/collect ... burl-short

Hands down my money would be on a Jet. Ok i've not had the best of luck (Owing to Axminster fitting very subpar parts on warrenty/TNT dropping one lathe..) But i use my 1014i (The predecessor to the 1015) daily on a professional basis. The motor is strong and stable, all castings are a great...

The eventually reply came. It sounds as if they got the bearings from Jet as they are going to report my findings back to them, if thats the case that is disappointing. however they sent me £30 gift card to redeem my costs in the bearings and inconvenience (This) time. Have picked up a ring...

Silly me :mrgreen:

To fuel the fire (aayyye) as a jeweller I used to keep a tea light on to light torches quickly. For a period I would sit them on my bench peg (off cut from an old wood window frame) It duly caught fire about 8 months ago with a tea light from a pack I'd been using for months perfectly fine...

Have done, but since that email went out at 4pm on a Friday I wasn't expecting a reply any moment soon ha.

Ok.... Bearing swap was pathetically simple.. some hiccups, Axminster's rubbish bearings had corroded against the spindle and took a minute to soak in wd40 and hammered out, i also found a small section of the seat for the rear bearing had been broken in the previous bearing change by Axminster...

Out of nowhere Axminster offered me a full refund on receipt of its return, unfortunately owing to the fact I'd have to buy a new lathe, thread adaptors etc (and them not specifying how a refund would be made) it would still cost me money and down time still ha. New bearings (and belt because...

On further investigation, it looks as if Axminster has fitted unsuitable bearings. the coding is RS - designating they are sealed one side and open the other, also it looks as if many of these bearings seals are high friction, this would explain the high temperature in use and rapid failure as...

See, this is roughly the kind of thing i expected from Jet, especially knowing people with machines up to a decade old with zero issues. I have checked the aliment of the centers with the tailstock, the headstock is properly aligned, the belt drives are properly aligned as well as in good...

It's incredibly rare for me to turn between the centers, when i do so i am using mini 4 prong drives with pilot holes into the wood and everything is tightened up enough to hold steady but not put pressure against the bearings. (no slowing in the lathe, certainly no "clunks" on the bearing from...

Unfortunately Budget rarely allows the amount to purchase a 2nd machine that would either sit earning £0 or replace a lathe prone to failure (and going by my luck, a second lathe would have just as many problems ha)

For what it is worth, the bearing on the chuck side of the headstock has always run hot, on both lathes, the opposite nothing. I have friend's with Jet lathes of the same, and similar sizes who report years (5+) with similar usage and trouble free running for years, with only switches...

Greetings, long time, no post. I have a Jet 1014I lathe (In fact i have had two...) The first was delivered from axminster with a loose motor fan and an electrical fault, this was fixed under warranty, returned to me on some 4x4 and 1x2 soft wood, and was well.... in poor shape on its return...

thanks, all natural too, sand upto 2000 grit, then polish and buff with carnauba wax. ive made a couple sets of nipple shields over the years (including an gaboon ebony one with pink ivory dot inlays, that was fiddly) found it best to shape and finish the back first, part it off, then work the...

dragging this up, couple years old, let the forum slip (tbh i let most forums i used slip) recently finaly set up shop all proper like, now doing the jewellery making as my fulltime job. i know its not most peoples cut of tea here, but you all seemed to enjoy the craftsmenship in my work...

Hello all, been a while since i last posted. my old 3 wheel powerline bandsaw is dieing a slow death, and i really do need an upgrade, needs to be bench top due to space, ive been eyeing up the RP bs10 and the bs250. however i notice a number of other mechines that look, and have much the same...