Search results

Hello I need your help, I am renewing my Garden bench, I have two iron ends and removed the decayed slats, they are 2 1/4 x 3/4 inches, 4 feet long what kind of timber would be suitable? and would a firm supply them to size? Please advise me. guyos

Thanks Guys I have changed the blade all is fine. guyos

Hello Can someone please tell me To change my table saw blade, which way do I undo the nut, clockwise or anti clockwise? Thanks guyos

Shed9 Many Many thanks. It is the right blade and I have ordered from Solent. I had searched everywhere through google and could not find it. Now I don't need to dump my jointer. Thanks again. Guyos

OH Dear Finally tracked down my blade. 156x16.5x3mm Problem is its from Alibaba and I would need to order 10 pairs minimum. Now the search is on for a retailer who buys from Alibaba and resells. Any leads Please. Guyos

Thanks guys I seem to have got it set up, a straight edge placed on top of the outfeed table and blade moves a 1/4 " when I turn the cylinder. Nice video Steve. My only problem now is to find blades to fit my B&Q machine. that seems impossible.

Thanks for the explanation, I was a bit confused, but it does not seem to matter where I set the in feed table. guyos

Hello can someone please tell me : When setting the jointer knives, should I have the machine depth of cut set to minimum or maximum? I have had it set to zero is that right? guyos

I have a Jointer bought from B&Q Performance Power Bench Planer/Jointer NLH1280J 1280W does anyone know where I can buy replacement blades? I have searched everywhere, the nearest I got was a sip blade that looks identical thickness width slots except for the length which is 3mm longer...

Thanks Sunnybob I have found my mistake. The first knife came out with the fence in place, but I have since removed the fence and found a screw that I was missing. All went well from then, all set up now. Thanks again. guyos

Hi i have a B&Q jointer performance power 1280 no hand book. I am trying to set the blades, but I did one blade turned the 4 screws and everything went well blade came out and I was able to reset it. Now when I try to do the other blade, same procedure undo the screws as normal, nothing...

Thanks JSW

Thanks Tudor, yes when I bought the rod at B&Q I thought it was a 3/8 rod. It was the nuts that I had to use that made me twig they were M10 nuts. My kerf is exactly 1/8 measured by calliper and micrometer. My apology for a saw would not lend itself to any arbor adjustments. It did take a...

Hello folks I have built a box joint jig, but I am unable to get a joint that fits. I have been advised the number of cuts and turns to make but joints are too loose. I suspect that because my saw kerf is 1/8" and the rod an M10 (don't know the TPI) that could be the cause of the problem. If I...

Thanks retire2004 I understand it now will have a go tomorrow. Guyos

Hello all I have made a finger joint jig with a 3/8 threaded rod seems to be working fine. My saw blade is 1/8" two turns of the rod. Can someone please tell me the procedure to cut 1/4" fingers I know that two turns give me 1/8" but don't know how to apply it in cutting. I tried 4 turns...

Got mine today, they're ideal and cheap enough to last me some time.

I got mine from the brighton marina store. I never knew Asda would sell this type of thing, until I saw a woman with one on her trolley, I asked an attendant where were they, and he said "oh they are in a sale , we only have a few left", and he pointed me to it, there were 5 on the shelf, I was...

Hi all A surprise at Asda yesterday. Dakota folding workbench for a fiver, check it out, it is quite sturdy and manouverable, got it just in time, me old B&D was on the blink.

Thanks doorframe I have them on order. guyos