2012 January Challenge ( Post Pictures HERE)

UKworkshop.co.uk

Help Support UKworkshop.co.uk:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Status
Not open for further replies.

Blister

Established Member
UKW Supporter
Joined
10 Nov 2006
Messages
7,436
Reaction score
433
Location
Boston Lincs
Challenge for January is a bowl

Our Judge for January will be Paul Hannaby

Must be New work for this Challenge

Maximum size 300cm ( 12" ) diameter

Any wood type ( Wood type and cost / value will not be taken into consideration ) as this challenge is all about design / shape / form / turning and finishing skills

Must be turned on a lathe from a single piece of wood / blank

No enhancements of any type allowed other than sanding sealer and a clear ( Non coloured ) Finishing product

Entry to be fit for purpose of holding solids and fluids

Any entry's that look more like a vase or a platter or are outside the rules and requirements will not be judged

The Judges decision is final ( Any negative comments re judging must be via PM only and not on the open forum )

NO Critique or comments on any work until February Please, After the Judging and results.

Please state wood type if known, dimensions and a little about how you made it and what tools and finish you used ( this helps the judge )

Please post 3 images of your work
1 side profile
1 showing the item looking down inside ( general view )
1 With the bowl turned upside down showing the bottom

Image size please use image size 640 x 480 0.3 mp, same previous months

Please notify me your entries are ready ( if our new scoreboard is not up and running by then ) by 10 pm on the 27th January after this time the thread will be locked

Entry’s to be uploaded from 10pm on 27th Jan up until 10pm on the 29th Jan. after this time the thread will be locked for Judging

Results will be given on 31st January
 
Good luck to all.

Here is my Pepperwood ( hard wood ) bowl for Jan. challenge.
It measures 8" x 3 1/2", I used a 1/2" bowl gouge for all of this bowl and scraped the outside with the gouges blade edge on its side to finish. Oh,I also used a small scraper and a skew chisel to complete the rebate in the bottom.

There is a reason why this bowl grain is not centred in the piece, wood is very scarce over here and this was my largest piece of wood, I did not want to make it too small.
Sanded from 180 to 400 grits and applied a few coats of BLO. and buffed to a finish. I do not personally like the VERY shiny finish for utility bowls like this, I prefer the matt finish so that it can be washed up now and again.

Leo
 

Attachments

  • topviewJAN.JPG
    topviewJAN.JPG
    52.7 KB · Views: 3,141
  • sideviewJAN.JPG
    sideviewJAN.JPG
    51.5 KB · Views: 3,141
  • bottomviewJAN.JPG
    bottomviewJAN.JPG
    51.5 KB · Views: 3,141
For my bowl I have chosen a piece of yew. The finished size is 7 1/2” diameter X 3 3/4” high. Turned entirely with my 3/8” spindle gouge.

Sanded down to 400 followed by 0000 steel wool and burnished with shavings. 2 coats of celulose sanding sealer, 2 coats of hard wax oil on the outside and 2 coats of melamine laquer on the inside. Buffed on my Beal system inside and out. This will get over the possible problem of using yew and make it food safe.

Janbowl1.jpg


Janbowl2.jpg


Janbowl3.jpg
 
Here is my little entry for the January 2012 competition. Wood not known (but I believe it is ash), overall size approximately 200mm diameter by 50mm overall height. Bowl section is approx 90mm diameter and 40mm deep, almost semi-circular; diameter was determined by the grain pattern I found on truing up the top face after completing the outside.

Both outside and inside were turned with ½“ and ¼” bowl gouges, final cuts being made with a freshly-sharpened traditional grind ¼” gouge. Sanded from 120 to 600 (part power sanding, part hand sanding) ; sprayed with acrylic sanding sealer and then lightly sanded again with the finer grits, and then Abralon 1000 and 2000. Finished with two coats of clear Chestnut wax, buffed on the lathe with a buffing wheel in a cordless drill and the lathe running quite fast.

Doesn’t come out too well on the photos, but some of the grain has a delightful greenish tinge to it.

Mike.
 

Attachments

  • Jan 2012 - Bottom view.JPG
    Jan 2012 - Bottom view.JPG
    102.8 KB · Views: 3,093
  • Jan 2012 - side view.JPG
    Jan 2012 - side view.JPG
    82.4 KB · Views: 3,093
  • Jan 2012 - general view.JPG
    Jan 2012 - general view.JPG
    102.6 KB · Views: 3,093
entry no, 1 for 2012 challange 057.jpg
entry no, 1 for 2012 challange 056.jpg
entry no, 1 for 2012 challange 055.jpg


this is made from rippled ashand measures 280x100.
sanded to 400 grit 2 apps. of sanding sealer cut back
finished with woodwax and burnished with paper towel.
 

Attachments

  • entry no, 1 for 2012 challange 055.jpg
    entry no, 1 for 2012 challange 055.jpg
    83.3 KB · Views: 3,112
  • entry no, 1 for 2012 challange 056.jpg
    entry no, 1 for 2012 challange 056.jpg
    93.4 KB · Views: 3,113
  • entry no, 1 for 2012 challange 057.jpg
    entry no, 1 for 2012 challange 057.jpg
    88.1 KB · Views: 3,095
The wood for my bowl is Mahogany, its 9.5" X 2.5".
I attached the blank to a screw chuck to round up and profile the outside edge, also to cut tenon.
Mounted in O'donnell jaws and hollowed with 3/8" and 1/4" bowl gouge and a little touching up with a round nosed scraper.
I was going to remove the tenon by mounting in a set of cole jaws but it is 1/2" too wide to fit, so a lot of sanding with a rotary sander to finish the bottom.
Sanded through the grades from 80 up 400, then applied sanding sealer and sanded 400 to 600 grit with Arbranet.
Liberon Bison wax applied on the outside and food safe oil on inside to finish.

Good luck to everyone.
 

Attachments

  • Jan3.jpg
    Jan3.jpg
    94.1 KB · Views: 3,074
  • Jan2.jpg
    Jan2.jpg
    89 KB · Views: 3,075
  • Jan1.jpg
    Jan1.jpg
    111.2 KB · Views: 3,074
Here is my entry for this month. The wood is Beech and measures 8 1\2" x 3". Initially turned on a screw chuck the outside shape was turned and finished to 600. It was then reversed using the foot and the inside finished to the same grit. It then had three coats of Hard Wax Oil applied before being buffed using the Chestnut Polishing Kit. Tools used included both 1/2 and 1/4 bowl gouges, a Simon Hope small round bar skew \ scraper and the bowl was power sanded inside and out.

Hope you like it.

Steve
 

Attachments

  • DSCN0069.JPG
    DSCN0069.JPG
    129.9 KB · Views: 3,059
  • DSCN0071.JPG
    DSCN0071.JPG
    127.7 KB · Views: 3,059
  • DSCN0043.JPG
    DSCN0043.JPG
    149.6 KB · Views: 3,059
Hi,

Bowl made from London Plane, it's 6" x 1 3/4".

Mounted on a screw chuck and turned round and the tenon cut. Then mounted on my SP chuck with the standard jaws and hollowed out with a 3/8" bowl gouge, and scraped with a roundnose. Sanded to 600 grit, a couple of cut coats of danish oil as I ran out of sealer and a top coat of Ren Wax.

Good Luck to all the newbies like me, and hope all the seniors from last year keep the level high!

PHIL
 

Attachments

  • DSCF7195.JPG
    DSCF7195.JPG
    107.4 KB · Views: 3,056
  • DSCF7193.JPG
    DSCF7193.JPG
    113.9 KB · Views: 3,056
  • DSCF719.JPG
    DSCF719.JPG
    112.4 KB · Views: 3,055
My first ever competition entry. Finally!! And I did it with two hands!! :D

This bowl is padauk, approx 5" diameter, 2" high and internally 1.25" deep.

Started on the screw chuck to turn the outside and base, then onto the chuck for the inside.

Tools use were 3/8" & 1/2" gouges, parting tool and round nose scraper.

Sanded from 120 to 600. 2 coats of shellac sealer and finished with 6 coats of beeswax, cut back with 0000 between all coats.

Good luck to everyone.
 

Attachments

  • jan 2012 - bottom.JPG
    jan 2012 - bottom.JPG
    29 KB · Views: 3,046
  • jan 2012 - side.JPG
    jan 2012 - side.JPG
    27.4 KB · Views: 3,046
  • jan 2012 - top.JPG
    jan 2012 - top.JPG
    30.1 KB · Views: 3,046
Vary poor rushed token entry for me again :(

Not sure of the wood but is was cut off a log and turned green. It was very wet so no finish either.

Due to lathe limits its more a pinch bowl :lol:

4" diameter by 1-3/4" Bowl is around 1-1/4" deep.
 

Attachments

  • BowlJan1.jpg
    BowlJan1.jpg
    97.9 KB · Views: 3,029
  • BowlJan2.jpg
    BowlJan2.jpg
    99 KB · Views: 3,029
  • BowlJan3.jpg
    BowlJan3.jpg
    85.2 KB · Views: 3,030
Hi,

Bowl turned from a piece of ash approx 7"dia x 4"tall, majority of work completed with 3/8" bowl gouge and a scrapper to finish then sanded to 240 grit and a coat of beeswax applied

SideJanComp.jpg


TopJanComp.jpg


BaseJanComp-1.jpg



Dave
 
Here is my bowl

Made from native Walnut and finished with s/s and 22 wax

The outside was turned on a screw chuck. The foot had a spigot to mount in chuck. The bowl was hollowed initially with bowl gouge and then my rolly hollowing tool to create the undercut under the lip and to follow the outer curve. The top photo I have taken from an angle to try to show the undercut. it was then finished inside before reversing to take off the spigot and to finish the foot.

Dimensions: 190 mm x 75 mm, 125mm bowl opening

IMG_0799.jpg


IMG_0787.jpg


IMG_0785.jpg
 
I turned a small bowl from spalted Beech, it measures 5 1/4” diameter by 2 1/2” high. It was mounted on a screw chuck and the bottom shaped including a tenon. Then reversed and mounted in dovetail jaws of the chuck. The top half was shaped to hopefully match the bottom shape. The inside was hollowed to match the outside shape.
Tools used 1/2” Bowl Gouge, straight scraper and skew for the tenon, and a BCT hollower.
Sanded from 120 – 400. 1 coat of sanding sealer. 2 coats of friction polish. Finished with wax.

Side.jpg

Top.jpg

Bottom.jpg


Cheers David
PS I just hope the pictures are attached #-o
 

Attachments

  • Side.jpg
    Side.jpg
    51.3 KB · Views: 3,013
  • Top.jpg
    Top.jpg
    39 KB · Views: 2,995
  • Bottom.jpg
    Bottom.jpg
    42.8 KB · Views: 3,021
Hi , This is my entry for this month, and as wood used is not part of the judging I have chosen a Ash blank

11 1/2 " Diameter x 2 1/2" high

Internal bowl hollowed with a undercut rim

Externally shaped with a slightly tapered in top rim with 2 beads

Bowl reversed onto Cole jaws and the chuck mount removed sightly concave to allow a stable foot

Sanded from 120 to 400 final sanding done in forward and reverse to remove any raised grain , sanding sealer , the Hard wax oil x 2 coats , and buffed on my polishing machine
 

Attachments

  • IMG_1418.JPG
    IMG_1418.JPG
    55.8 KB · Views: 2,966
  • IMG_1419.JPG
    IMG_1419.JPG
    75.7 KB · Views: 2,966
  • IMG_1420.JPG
    IMG_1420.JPG
    67.6 KB · Views: 2,966
My January offering to the gods, an unadulterated bowl. spalted sycamore i think, rescued from the firewood pile. 4" faceplate to start, bottom shaped with 3/8 superflute bowl gouge and an inch square scraper, recessed and finished, reversed and mounted on expandy chuck, hollowed with superflute and round scraper. sanded to 400, then MM pads, cellulose s/s and a fiddes soft wax finish. approx 6.5" x 2.5"

jan bowl bottom.jpg


jan bowl general.jpg


jan bowl inside.jpg
 

Attachments

  • jan bowl inside.jpg
    jan bowl inside.jpg
    220.2 KB · Views: 2,942
  • jan bowl general.jpg
    jan bowl general.jpg
    203.4 KB · Views: 2,941
  • jan bowl bottom.jpg
    jan bowl bottom.jpg
    190.7 KB · Views: 2,960
Hi all. My entry is a flared bowl turned from American Maple. 200mm dia x 60mm. Blank was mounted on a screw chuck to shape the outer profile & foot mainly with 3/8 bowl gouge. Re-mounted in Oneway chuck on foot spigot to shape inside of bowl using the same tool. Used home made cole jaws to finish foot. Sanded from 120g to 400g. Then 2 coats of sanding sealer & polished using a lathe mounted polishing mop.

Dave



top view bowl.jpg

Side View Bowl.jpg

Bottom View Bowl.jpg
 

Attachments

  • top view bowl.jpg
    top view bowl.jpg
    64.3 KB · Views: 2,653
  • Side View Bowl.jpg
    Side View Bowl.jpg
    56.6 KB · Views: 2,644
  • Bottom View Bowl.jpg
    Bottom View Bowl.jpg
    57.1 KB · Views: 2,642
More manitoba maple(box elder), sorry guys but I love the stuff and its free. A tree blew over in November and I scooped the bottom 4 feet and here is some of it. Roughed out Jan 6 and finished Jan 13 in a couple of hours. Needless to say, turned wet on a screw with a tenon. Reversed and hollowed and it started to move immediately. Put it in the cole jaws and turned off the tenon. Sanded to 320 and just watched it move for a week. Sprayed with lacquer. I love the little warts on it and the colours and the the knots and the warpage(is that word?).6" diam by 5"high by 1/8" thick. turned with 3/8" bowl gouge. Thanks DK
 

Attachments

  • P1010878.JPG
    P1010878.JPG
    166.5 KB · Views: 2,564
  • P1010882.JPG
    P1010882.JPG
    173.6 KB · Views: 2,565
  • P1010880.JPG
    P1010880.JPG
    169.7 KB · Views: 2,564
My entry, Sycamore approx 7"x1.5" done with a 3/8 bowel gouge on a screw chuck finish to 320 grit with Melamine Lacquer on the out side and sanding sealer on the inside.

100_0004640x480.jpg
100_0005640x480.jpg
100_0006640x480.jpg
 

Attachments

  • 100_0004640x480.jpg
    100_0004640x480.jpg
    102.4 KB · Views: 2,558
  • 100_0005640x480.jpg
    100_0005640x480.jpg
    99.5 KB · Views: 2,571
  • 100_0006640x480.jpg
    100_0006640x480.jpg
    101.3 KB · Views: 2,573
Here is my entry for the bowl challenge.
Turned from ash, using 1/2" and 3/8" bowl gouges, plus a small round skew for the base and detailing.
Sanded to 400 grit, then finished with cellulose sealer, Renaissance Wax, and buffed.
Dimensions: 240mm diameter and 60mm high.
ashbowl1.jpg

ashbowl2.jpg

ashbowl3.jpg
 

Attachments

  • ashbowl1.jpg
    ashbowl1.jpg
    237.6 KB · Views: 2,713
  • ashbowl2.jpg
    ashbowl2.jpg
    216.7 KB · Views: 2,569
  • ashbowl3.jpg
    ashbowl3.jpg
    189.5 KB · Views: 2,548
Here's mine, approx 6.5" diameter and 3" high in Field Maple.
Turned using mostly a crown Ellsworth bowl gouge, with a little scraping and too much sanding (down to 600 grit) as the tear out was horrendous.
Reverse chucked wit a pointy tool used for the grooves in the base.

Finished with Chestnut woodwax 22, no sanding sealer.
 

Attachments

  • 201201 bowl top.jpg
    201201 bowl top.jpg
    18.5 KB · Views: 2,534
  • 201201 bowl side.jpg
    201201 bowl side.jpg
    10.6 KB · Views: 2,534
  • 201201 bowl bottom.jpg
    201201 bowl bottom.jpg
    14.2 KB · Views: 2,534
Status
Not open for further replies.
Back
Top