Workshop time

UKworkshop.co.uk

Help Support UKworkshop.co.uk:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

Dalboy

Established Member
Joined
18 Sep 2008
Messages
3,912
Reaction score
251
Location
Canterbury United Kingdom
Well have managed some workshop time at last finished putting a background colour on a hollow form that went bang.

This is the one that went bang and what shape it is now. And no I did not go through the side a second of loss of attention and I caught the rim.

20191220_150444 (1024x768).jpg

20191222_152920 (768x1024).jpg

20191223_124250 (1024x768).jpg


And while that is drying started another hollow form which I intended to do some carving on but as you can see it does not need anything doing to it other than finishing as I have soaked it in sander sealer as it is punky in places the bottom half has worked now it is turned around I can tomorrow give it a quick run over with a freshly ground tool.

First picture of the bottom half and the other three after turning around and shaping the top half you can see the grain pulled out in some of the photos

20200106_140638 (768x1024).jpg

20200106_151500 (768x1024).jpg

20200106_151455 (768x1024).jpg

20200106_151504 (768x1024).jpg
 

Attachments

  • 20200106_140638 (768x1024).jpg
    20200106_140638 (768x1024).jpg
    216.1 KB · Views: 491
  • 20200106_151455 (768x1024).jpg
    20200106_151455 (768x1024).jpg
    215.2 KB · Views: 518
  • 20200106_151500 (768x1024).jpg
    20200106_151500 (768x1024).jpg
    199.6 KB · Views: 491
  • 20200106_151504 (768x1024).jpg
    20200106_151504 (768x1024).jpg
    198.3 KB · Views: 491
  • 20191220_150444 (1024x768).jpg
    20191220_150444 (1024x768).jpg
    178.1 KB · Views: 491
  • 20191222_152920 (768x1024).jpg
    20191222_152920 (768x1024).jpg
    221 KB · Views: 491
  • 20191223_124250 (1024x768).jpg
    20191223_124250 (1024x768).jpg
    134.8 KB · Views: 491
That’s some dramatic looking wood!

Hollow forms are beyond my skill level at the moment, but very interesting.
 
Shame about the catch. You had those sides very thin.

Nice new piece though. It's going to be interesting to see the end result. Good luck.
 
Thank you both.

Yes, the second one I am working on is a little punky so sharp tools are a must as well as stabilising.

I was getting the first hollow form to a nice consistent thickness with plenty of stops and measuring just annoyed with myself for allowing to be distracted for a split second as the hole was not that big
 
Yes, moment of lack of concentration on what you're doing, for one fraction of a second is all it takes.
The problem is we get cocky and you blink as you're going in or out and "bang!" it's gone.
 
Progress on the hollow form. This afternoon hollowing completed but still needs sanding under the rim but the homemade sanding tool needs modifying to fit in the opening. Not sure if to put a small lid with a twisted final on it. May just make one and see what it looks like.

20200108_145634 (768x1024).jpg

20200108_145619 (768x1024).jpg


RickG":22yg1g39 said:
Yes, moment of lack of concentration on what you're doing, for one fraction of a second is all it takes.
The problem is we get cocky and you blink as you're going in or out and "bang!" it's gone.

Certainly not getting cocky just lack of concentration for a couple of seconds.
 

Attachments

  • 20200108_145634 (768x1024).jpg
    20200108_145634 (768x1024).jpg
    167.1 KB · Views: 318
  • 20200108_145619 (768x1024).jpg
    20200108_145619 (768x1024).jpg
    174.3 KB · Views: 317

Latest posts

Back
Top