Proposed sideboard. Thoughts

UKworkshop.co.uk

Help Support UKworkshop.co.uk:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
flanajb":2exp6ifb said:
I have designed this piece which I intend to construct from maple (carcass), walnut (stand and inlay around doors) and poplar burr veneer.

Interested to get peoples thoughts on this.

6710262295

Bit of a problem there? I think you need a URL not an IMG tag.

http://www.flickr.com/photos/63922880@N02/6710262295/

Mick
 
MickCheese":36tgj4lw said:
flanajb":36tgj4lw said:
I have designed this piece which I intend to construct from maple (carcass), walnut (stand and inlay around doors) and poplar burr veneer.

Interested to get peoples thoughts on this.

6710262295

Bit of a problem there? I think you need a URL not an IMG tag.

http://www.flickr.com/photos/63922880@N02/6710262295/

Mick
Thanks. The flickr image tag would not work so I changed it to a URL
 
I like it very much. I'm not sure about the mould on the plinth. Maybe plain to maintain the contrast with the impact of the main cabinet.

Very nice. You may have a problem finding a non-yellowing finish.
 
Only thing I'm not keen on is the exposed sliding dovetails, I would stop them short of the front so the edge of the top & bottom carries straight through.

Might also lift the carcase off the legs slightly to make it a bit lighter looking.

J
 
Thanks for the comments.

Finish - Planning on using morells water based laquer. Will bring out the grain of the poplar burr very nicely.

Jason - I agree that lifting the carcass off the legs will make it look lighter. Good idea

Undecided on whether to have a visible sliding dovetail or not. I do like them, but that is most likely because my Leigh dovetail jig is arriving tomorrow and I am keen to put it to good use. The cabinet sides will be done with half blind dovetails.
 
If you dont mind me adding my twopenneth my only concern regarding your design would be having all the drawers the same depth.

If you make it like this when finished it will appear (trick of the eye) that the bottom drawer is shallower than the top drawer, you want to stagger the depths slightly bottom drawer deepest and top drawer narrowest etc.

Rog
 
Dodge":2nh3is5t said:
If you dont mind me adding my twopenneth my only concern regarding your design would be having all the drawers the same depth.

If you make it like this when finished it will appear (trick of the eye) that the bottom drawer is shallower than the top drawer, you want to stagger the depths slightly bottom drawer deepest and top drawer narrowest etc.

Rog
Hi Rog, thanks for your comments. Is there a formula you can use to adjust draw heights according to the height of the unit so that they appear equal width when viewed from a standing position?
 
jasonB":54n9rlpv said:
There is a way to get the progression of sizes by using a compass, I'll see if I can find an illustration if not I'll sketch it out. Can you give a height of teh carcase and draw width.

As a rule of thum keep the centre draw as drawn, make the top 15mm smaller and the bottom 15mm bigger for three draws. I used a similar principal on teh folowing two

http://img.photobucket.com/albums/v156/ ... /ppg09.jpg
http://img.photobucket.com/albums/v156/ ... /bill1.jpg

J
The overall height is 900mm with the carcass being 700mm. Thanks
 
I constructed something to demonstrate the apparent height of the drawers compared to the actual height.



From the viewpoint I selected--about my eye height--and a given distance from the piece, the apparent difference in height between the top and bottom drawers is less than 25mm. In reality there's about 80mm difference.
 
flanajb":3mcpshxq said:
I do like them, but that is most likely because my Leigh dovetail jig is arriving tomorrow and I am keen to put it to good use. The cabinet sides will be done with half blind dovetails.

Jig left this morning :D thanks
 
you can do a stopped sliding dovetail on the leigh jig cant you? Obviously stopped at one end only :)
 
Yes easy to do stopped DT on the Leigh or just route it right through and use the veneer to cover the end.

J
 
jasonB":33dtq7yd said:
Yes easy to do stopped DT on the Leigh or just route it right through and use the veneer to cover the end.

J
Only solid maple for this carcass. None of that mdf stuff!

Maybe that is rather extravagant, but as I am using blind dovetails to build the carcass I don't know how else I could do it?
 
Back
Top