Post a photo of the last thing you made

UKworkshop.co.uk

Help Support UKworkshop.co.uk:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Fantastic!! Where do you purchase your pig suede from, if you don’t mind telling? Cheers Robyn
Thanks.
I bought the whole pigskin from ebay for £40 inc delivery…
https://www.ebay.co.uk/itm/Pig-Sued...2349624.m46890.l49286&mkrid=710-127635-2958-0
However i got a courteousy call from them to provide advice and make sure it’s the correct product for my needs (very helpful). They also said it would be cheaper if i bought direct next time and they had a much larger range direct than what they list on ebay, so will give them a call next time…
http://www.schallandson.com/
 
Made another podlet today, chose a piece of sherry that was cut back in August, unfortunately it started to split as I was turning it but it held together and I managed to finish it, heavily soaked it in Danish oil, hopefully it won't crack any more, also broke my live centre while roughing the branch down 😥😥😥
20220509_191025.jpg
20220509_191032.jpg
20220509_191105.jpg
20220509_191114.jpg
20220509_191144.jpg
20220509_191156.jpg
 
made another microphone box, lined using custards methods of lining boxes in the sticky thread, it'll be sent out to the USA soon.
 

Attachments

  • U47box-3.jpg
    U47box-3.jpg
    82.2 KB · Views: 18
  • U47box-4.jpg
    U47box-4.jpg
    121.9 KB · Views: 21
  • U47box-7.jpg
    U47box-7.jpg
    72.7 KB · Views: 22
  • U47box-8.jpg
    U47box-8.jpg
    90.8 KB · Views: 22
  • U47box-9.jpg
    U47box-9.jpg
    116.5 KB · Views: 22
  • U47box-10.jpg
    U47box-10.jpg
    114.8 KB · Views: 20
  • U47box-12.jpg
    U47box-12.jpg
    116.2 KB · Views: 21
  • U47box-14.jpg
    U47box-14.jpg
    71.6 KB · Views: 22
  • U47box-16.jpg
    U47box-16.jpg
    77.3 KB · Views: 20
  • U47box-17.jpg
    U47box-17.jpg
    74 KB · Views: 19
Small little drawers I made as a gift, oak body and Bolivian rosewood faces with half blind dovetails.
 

Attachments

  • F484BAB2-EAE1-409F-96D8-C441C1E93448.jpeg
    F484BAB2-EAE1-409F-96D8-C441C1E93448.jpeg
    221.2 KB · Views: 0
  • A7821752-D670-40B3-A2E1-26F8CD0E0710.jpeg
    A7821752-D670-40B3-A2E1-26F8CD0E0710.jpeg
    146.6 KB · Views: 0
  • FC56E0E5-4A37-408E-948A-638373FDA2CC.jpeg
    FC56E0E5-4A37-408E-948A-638373FDA2CC.jpeg
    131 KB · Views: 0
A worse crime is if you read and understood the instruction.

And another crime is you missed the "be" on your post, "cause" is a totally different meaning to because.
 
This is what I have done a couple of times with end-of boards that have cracks and shakes in them. I cut out the offending section and glue other off-cuts between. This hides the fact the grain won't line up but also makes for a larger bowl. This is a bowl from a mahogany end piece crossed with two strips of teak (brown), three strips of what I thought was Sycamore but it has orange coloured flecks which I've never seen before. I know it is not Maple. It's 320mm wide and 70mm high.

P1080221.jpg
 
I needed an adapter for my cyclone dust extractor so I could use a 1000M3/H extractor. 100mm to 45mm. Even at low quality print, it took 4 hours. High quality would have been 12 hours. I use an old Aquavac at the moment. It works very well, but I thought the large extractor would work better.
It was garbage, just too much loss through the cyclone. I'll just make another adaptor for the bottom and use it as a funnel.

IMG_5899.JPG
 
Seen some very effective planks like that turned into a dinning room table with coloured epoxy or similar about 75mm wide joining them together, rough edges/bark left on.
 

Latest posts

Back
Top