Let there be light...

UKworkshop.co.uk

Help Support UKworkshop.co.uk:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

Charley

Established Member
Joined
24 Aug 2002
Messages
2,072
Reaction score
15
Location
Collingham
Along with the dodgy electrics, I've had a bit of a light problem in the workshop, in that if I'm in the workshop during the day I've had to check that the lights are indeed switched on after struggling to see pencil lines :lol:

Well not any more :D - With the help of my very kind neighbour who came around on his day off, over 100m of cable, what seemed like thousands of clips, a CU and 8 new double strip lights the workshop has been re-wired 8)

I can now go into the workshop without the fear of sockets blowing up in my face :roll: :lol:


click to enlarge

Nice and neat eh? One circuit for the ring main, one for the jointer, one for the TS, one for the lights, one for the alarm and one for the outside light (soon to become light*s*). Plently of room to add another ring main for the other halve of the workshop and of course more cast iron machines :twisted:


click to enlarge


click to enlarge


click to enlarge


click to enlarge


click to enlarge

Just need to finish painting the walls then I can put every thing back in place and THEN I may just start finishing some projects :oops:

BTW for those of you that were wondering, my neighbour is a sparky :lol: so don't worry it's all been checked & tested :)
 
ahh another excuse to show off that massive workshop! Looks good Charley! :wink:
 
Charley

Have you got round to painting lines on the floor yet to remember which way to go round the shop? :)

I'm thinking that it would be a good idea to fit up a spot lights that shine on the operating sides of my bandsaw & trtion table saw fences.

Room/ceiling lights four feet above works surfaces are not adequate in my double garage.
 
Like you, I've just had reliable electrickery installed in my workshop (though not on such a grand scale) and it makes a world of difference.

In which corner of the workshop are you hiding the miniature power station needed to feed your establishment ;) :) ?

Gill
 
Nice one Charley - maybe too late now but I don't know if you or other forum members are familiar with these guys:

http://www.lightbulbs-direct.com

Their lamp prices are pretty good - c half the price of screwfix for halogen downlighters. But the main reason for using them is their range of fluorescents and low energy bulbs. Lost of full spectrum and daylight bulbs etc and at pretty reasonable prices (imo).

Cheers

Tim
 
devonwoody":34pypqdf said:
I'm thinking that it would be a good idea to fit up a spot lights that shine on the operating sides of my bandsaw & trtion table saw fences.
Yeah the idea is to put some extra light fittings above the table saw, mitre saw and bench but the new lights we put up yesterday have made a huge improvement...
philly":34pypqdf said:
You gonna board over the ceiling or leave it open??
The plan was to board over although I'm not sure now.

tim":34pypqdf said:
Nice one Charley - maybe too late now but I don't know if you or other forum members are familiar with these guys:

http://www.lightbulbs-direct.com
Thanks for the link Tim. I've made a note of it. The light fittings cost about £16 +VAT and they included the tubes.

frank":34pypqdf said:
charley did you move the aeroplane outside
No that's in the other halve :p :lol:
 
Charley":2sykzvt3 said:
philly":2sykzvt3 said:
You gonna board over the ceiling or leave it open??
The plan was to board over although I'm not sure now.
Charley,

How high are the rafters? If they are under 9' I would not board a ceiling as it limits the turning space for long boards. My shop has rafters at 8' and I often poke stuff up through them as I turn end to end.

What I have started to do is insulate under the tiles and board that. I am going to paint that white to improve the reflected light.
 
Hi Charley,
I thought I would ask the question that everyone else seems to want to know. I do not mind being called a nosey parker I have got broad shoulders and to be honest I am being nosey, how big is that aircraft hanger you call a workshop.

All the best,

Rosco ( Chris ).


Charley":2kx812i9 said:
devonwoody":2kx812i9 said:
I'm thinking that it would be a good idea to fit up a spot lights that shine on the operating sides of my bandsaw & trtion table saw fences.
Yeah the idea is to put some extra light fittings above the table saw, mitre saw and bench but the new lights we put up yesterday have made a huge improvement...
philly":2kx812i9 said:
You gonna board over the ceiling or leave it open??
The plan was to board over although I'm not sure now.

tim":2kx812i9 said:
Nice one Charley - maybe too late now but I don't know if you or other forum members are familiar with these guys:

http://www.lightbulbs-direct.com
Thanks for the link Tim. I've made a note of it. The light fittings cost about £16 +VAT and they included the tubes.

frank":2kx812i9 said:
charley did you move the aeroplane outside
No that's in the other halve :p :lol:
 
To be honest I only measured it a couple of months ago, when I was playing with SketchUp


workshop1.jpg


It's roughly 21' x 35' give or take a couple "

The only bad thing with having a big workshop at my age is that I'll have to downsize one day :cry:
 
BTW for those of you that were wondering, my neighbour is a sparky so don't worry it's all been checked & tested
Hi Charley, Professional job mate,I just hope your meter has got a soft start on it for when you really get switched on. I too am or was untill I retired a sparky, worked on everything from millivolts to megavolts, but now sadly because of the new regs. am not even good enough to install my own electrics.

Cheers Alan.
 
gwaithcoed.

Your comments re the new electric regulations demonstrate how daft it is when politicians without piratical knowledge are let loose on tradesmen etc.

However my feeling is that nothing has really changed re rewiring because in the old days if you took out the elecrtric company fuse to do some rewiring you had to call the company back to seal up the company fuse and they could elect to do a wiring check.
Now you have to get your wiring checked and certified by a qualified electrician.
 

Latest posts

Back
Top