Cleaning sealed ball bearings, questions about stuff.

UKworkshop.co.uk

Help Support UKworkshop.co.uk:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Thanks for your thoughts folks

Not being at all knowledgeable about this sorta stuff, so it's very nice to read that there's various ways of cleaning them out.

It would seem to me like white spirit will be best, as I don't have any solvents to get rid of any residue, should I use paint thinners for the job.
No compressed air, but think I might manage with patience and toothbrush instead.
Hot water just feels wrong to me, but will if nessecairy should I not get things shiny and not tacky.

Bought some lithium grease for 3 euros
Lithium EP2 multi purpose -20c to +140c in a brownish tube.
Guessing this is the stuff, but seen some red stuff which I was considering either.
Not to worry, I will see how things go.

Haven't made a wee tool for the job of seal removal yet, good to hear some warning
as those utubers seem a bit confident with a pick or blade.

Eager to see how good they turn out, and should they be pants, then nothing lost but a hour or two and a 3 quid tube.
Have some other bearings which I could also do if it goes well, so hopefully the grease tube can earn it's keep in the press.

Thanks for your comments folks
I'll make an update when I get back to this.

Tom
 
Note that paint thinner and mineral spirits are similar to the solvents I mentioned so disposal is still the same. You take the oily film (minimal) off with Acetone type solvent but why? You’re going to put grease on them anyway. If you’re going to Loctite them in then you would degrease the outside.
Pete
 
Many years ago, I was enrolled in classes at General Motors Institute and the instructor told us to NEVER wash out a bearing with any type of solvent as once dried, grease will not adhere to the bearing balls or rollers. I did in fact have to try that just to satisfy my own curiosity and it is true. I washed a ball bearing, wiped it dry with a lintless cloth and then blew it out with compressed air. I then tried to apply a good coating of wheel bearing grease and it would not stick. I forget now, it's been 60 years, what I finally had to do to get the grease to stick. Another type of cleaning, possibly hot soap and water. The solvent leaves something behind that will not allow the grease to adhere.
 
They start to look like a well sucked gobstopper. Good luck

I replaced bearings on my lathe that were shot with used bearings off an identical shaft - they looked absolutely perfect and rumbled to the point the lathe was unuseable. I can understand someone taking time and trouble to reuse old unobtainable or ridiculously expensive bearing, but for ffs for the work involved just replace them. Every time.
 
Many years ago, I was enrolled in classes at General Motors Institute and the instructor told us to NEVER wash out a bearing with any type of solvent as once dried, grease will not adhere to the bearing balls or rollers. I did in fact have to try that just to satisfy my own curiosity and it is true. I washed a ball bearing, wiped it dry with a lintless cloth and then blew it out with compressed air. I then tried to apply a good coating of wheel bearing grease and it would not stick. I forget now, it's been 60 years, what I finally had to do to get the grease to stick. Another type of cleaning, possibly hot soap and water. The solvent leaves something behind that will not allow the grease to adhere.
I wonder what the bearings were cleaned with before lubrication when assembed?
 
I must be tired, almost sounds like you want to replace some premium bearings with old dirty ones after you’ve fudged around with them?

Sounds about as good an idea as reusing a stretched bolt or a cracked o-ring.
 
Sometimes it's good to try to do this, just for the fun of it and to see if you can. It might work, it might not, but it's how you learn. Go for it!!!
 
OCtoolguy, kudos for mentioning this, I will be doing a wee spot test first,
to be sure now thanks a million.
Just for clarification there was no reason to have swapped these bearings in the first place, and I was thinking it was them which was to blame rather than all the other things
which was the reasons.

Thanks for mentioning all these solvents Pete, although familiar concoctions I've read of before, I had to google to make sure which each was.

Not sure if I mentioned that I planned to keep a very close eye on these bearings with the intention of getting new ones after a bit of testing and light use, say not challenging the machine and only running for say 30mins a week max kinda thing.

I will be taking the bearings out anyway, only installed the old one just to make sure I didn't damage the SKF newer one, whilst I was getting the fit right making a new spacer for the wheel.
Now I have the fit right, I am going to make two more,
the part made below could be more accurate,
(plastic got squished a bit in the vice whilst drilling, so the hole is a bit shoddy)
IMG_20220214_175624.jpg


I think there's more chance of getting everything a bit more solid with the original bearings.
Guessing there inst much mileage on this machine to begin with, as it was a Friday lemon, possibly only getting as much run time as I've put on the newer bearings.

Even though I've got the fit right for the top wheel, I might well end up faffing about with the bottom wheel, or possibly not going near it either.
Gotta do some alignment checks as the wheel will sit further out of the shaft with the new part,(I have another thread about those spacers),
and the pulley is sitting as far out on the motor shaft as I dare to use.
Quite a distance, one could possibly take a little of the face of the back of the shaft to sit the wheel in further, and get that pulley more on the shaft.
Have the original measurements written down for it, something like below as is now.
Probably not good.
SAM_4616.JPG

Gotta figure out those wee things, along with the play about with wheel protrusion on the top wheel and other tests, etc
so that might explain why I wish to use old bearings for a while...
plus I'm skint at the moment.

Thanks
Tom


SAM_5279.JPG
 
Last edited:
Today, I had to do a repair on my bike and happened to notice some rust muck coming from my bottom bracket which has a BB30 bearings (42mm Outside and 30mm inside Dia.) When I took the pedals off, and rotated the bearings, they were full of crud. I picked out the bearing seal, very very easy, without damage. I cleaned the bearings using anything I could spray inside, then high pressure air to get the grime out. The bearings are knackered, but it will keep me going for a while yet until I can get replacements and make a custom tool for removing the circlips and a make a bearing press on the lathe, or I might try printing a 3D tool.
 
Hi again, sorry been a bit late to reply back.
Have some photos of a bearing puller tool which I made from the end of a masonry nail,
and had a test of the tool.
There was a lot of crud, and possibly fatigue of the edge of the rubber, and possibly damage from me pulling them off too, didn't try cleaning them to inspect properly,
and put them away as had some dusty work to do.

At the same time as doing some turning my lathe bearings started rumbling,
not to mention the drill is needing attention aswell. (definitely replacments needed as are bad)
Quite instant I would say, well in the case of the lathe anyway, so I must investigate that.

As you might have guessed this made me have second thoughts about using the old ones, for something quite a bit more crucial than other applications, so going to stick back in the newish one, as I've still not made the other new spacers yet.

Hopefully I'll be able to report back with some queries I've made recently on a few threads, and depending on how critical those bearings for the other machines are,
might be worth trying on, now I've got a big tube of grease.
Typical! 🙂
 
Many years ago, I was enrolled in classes at General Motors Institute and the instructor told us to NEVER wash out a bearing with any type of solvent as once dried, grease will not adhere to the bearing balls or rollers. I did in fact have to try that just to satisfy my own curiosity and it is true. I washed a ball bearing, wiped it dry with a lintless cloth and then blew it out with compressed air. I then tried to apply a good coating of wheel bearing grease and it would not stick. I forget now, it's been 60 years, what I finally had to do to get the grease to stick. Another type of cleaning, possibly hot soap and water. The solvent leaves something behind that will not allow the grease to adhere.
Ive used WD40 to wash out open bearings in the past and then put grease back and that didn't stick either so must be the same solvent thing
 
I replaced bearings on my lathe that were shot with used bearings off an identical shaft - they looked absolutely perfect and rumbled to the point the lathe was unuseable.
Your method of removal might've prejudiced their future. One might withdraw a bearing by pulling on its outer race, but need to install it by pressing on its inner race, for instance. But I can't think either what you you were going to tell by 'looking' ...

Since bearings of the sort we're talking about (I think) last for ages & are cheap to buy, I've always just replaced with new ...

Re-use would be 'greener', but if it doesn't work do you really want to dismantle the machine again?
 
Looked was a broad term. They were perfectly clean and revolved without slightest hint of ever being used. I was scareful removing them - it wasn't difficult - and I didn't have new ones to hand at the time. The new ones were about £40 iirc.

Scareful? Careful.:LOL:
 
Last edited:
I’ve found a brake cleaner aerosol the best thing for cleaning Grease off small items….doesn’t leave any residue
 
Unless you have some VERY special tapered bearings ( e.g lathe headstocks ) - just replace them.

If you can't afford the bearing, you can't afford the machine

Very special ( and expensive ) bearings may warrant " repair " , but honestly this is rare.

The basic rule is NEVER mix lithium greases ( most common ) with bentonite greases ( usually sold as High temp bearing greases )
 
Cleaning sealed ball bearings is pointless by definition - if they need cleaning they have failed.
Though you might get a bit of extra mileage from them if you are lucky
 
Cleaning sealed ball bearings is pointless by definition - if they need cleaning they have failed.
Though you might get a bit of extra mileage from them if you are lucky
All my fishing reels have sealed bearings and clean out in lighter petrol then re oil with 2 drops of very fine oil for the spool bearings which get a hard kicking when casting but few drops more and performance drops off but makes them last over if left as was from new plus performance isn't so good from new.
but one way with bigger bearings is to douse in likes of comma hyper clean which apart from leaving anything clean it has an anti rust element in it then drop into a pot of heated grease so gets into bearing then once cooled bearing packed again.
 

Latest posts

Back
Top