Search results

Has anyone any experience with composite decking? Any good (or bad) suppliers? Solid or hollow? Thanks

Hi folks, car insurance renewal time for me, I need class 3 business use, who do you use? My quotes are all between £400-£450 (I'm mid 50's clean licence, full no claims on a mid range 4x4) Quoted from lv= Co-op Hastings Any other favourites?

I'm about to buy a festool ts55 so I'm doing my due diligence. Axminster - special offer around £300 (with one guide rail) Other sites - around £375-400 Ebay - around £400. ...... Except Several sellers wanting around £1,400 Wtf??? One of them, tools4trade has around 100,000 positive feed...

Any ideas on restricting a cupboard door to 90 degree opening? It's a face frame with inset door supported with butt hinges. I've tried a quadrant stay but getting the geometry right is driving me mad! Are there any easier solutions? Thanks in advance

Which router would you recommend for use with door/jamb hinge jigs? I already gave a table mounted 1/2" router but it's a bit heavy for doing the jambs. I'm not a professional, it's just for my house renovation, then to be used as a general purpose hand held router. Thanks

I've successfully split my granite worktop into two pieces (I'm moving the cooker) and now need to fill the joint between one of the pieces and a length perpendicular to it. Will colourfill do the job or is there something else? Google doesn't seem to throw anything up (too many hits on granite...

Or possibly a repeat of a previous one, sorry. I'm about to make some built in wardrobes (well the carcasses are already there, I've just removed the old sliding doors). The door will be 20mm mr mdf with 6mm panels. The face frames will be tulipwood, I think. Questions: 1) best supplier...

We cut quite a lot of 2mm mdf on our table saw. The existing extractor was built by Noah and has just given up the ghost. What do the learned panel suggest I replace it with? At the moment I also use a spindle moulder and router table, but only occasionally, and only for wood, both hard and...

My 2nd hand robland/startrite t30 spindle moulder has a knackered "top hat" (the bolt which screws intonthe spindle to keep the cutter head on) does anyone know where I could buy a new one? I've tried alt saws with no joy. thanks

Anyone have a manual or a link to a manual for the startrite t30 spindle moulder?

I need a sliding table spindle moulder for a project, I only need it for a couple of months, anyone fancy hiring one out?

I need this cutter http://www.whitehill-tools.com/catalogu ... ightbox/0/ But I need it to fit a 40mm euro cutter head. Anyone have any links/ideas? Thanks in advance

Hi Guys, Please reccomend a workshop Air filter. Small workshop (just the sawing room basically) (8m (l) x 3m (w) x 3m (h)) Table saw cutting hardboard mostly, occasional MDF. Crown guard and main dust extraction to industrial collector (bag over bag variety). Many thanks

Hi Guys, Anyone know the approx cost of fitting a DC brake to a Wadkin AGS10? Any links to appropriate companies? Ta

Hi guys, I'm making a couple of windows with storm sashes (top hung), can anyone point me to a drawing showing the fitting of the hinges? Where does the knuckle go? Are they rebated as normal? Thanks in advance

As per the subject, I need a new blade for my Bosch 10" Mitre Saw. General cross cutting. Any links welcome! Thanks

B&Q (and screwfix) have a De-Walt 18v cordless drill driver, 13mm chuck for around £100. (previously £200 at B&Q) Its the DC725 at B&Q, but the DC100KA at screwfix. The batteries are a bit weedy at 1.3Ah, but for a non pro not needing days and days of charge they look good value to me.

I asked recently on here for some advice on door locks for my new french doors. Jake posted that he had a set going cheap. Anyway I received them today, wrapped in 200m of bubblewrap, 100m cardboard, 4 lengths of cable sheathing and at least 1 roll of packing tape! Thanks Jake

Half was through ripping 100m of tulipwood for my french doors when the crappy tablesaw (rexon 10 inch 18 months old) caught fire! The fire didn't last long, but now the saw is obviously kaput. Anyone thinking of selling a table saw?

Hellow again, I've now ordered the Tulipwood for my painted french doors project (see earlier question). We now come onto the question of locking them. My wife would like two handles (one per door, obviously) which operate the slave and master together, or just the master as required (i.e. no...