Search results

I'm looking for the mechanism/hardware for a Louvre Roof System. I want one that retracts but also rotates each blind "blade". For now, just getting a look at market mechanisms... just to see how the work properly. I have an idea but always better to build off established knowledge. If one...

I'm planning out my bench and all photos I see of benches and their vices, (from my feeling) are the wrong way around... Like in the image below, to cut a piece of wood in the vice level. It has to project out into the open air, on the left-hand side. If on the right-hand side the bench gets'...

Has anyone any experience with this "new" motor? I am interested in buy one but because of it's newness, want to hear what folks feel about it. https://jessem.com/products/jessems-pow-r-tek-sr%E2%84%A2-router-with-variable-control-box

Can folks tell me the difference in performance between a full length cyclone separators... ... and the short, bucket mounted cyclone separators?

I am looking for a sharpening jig that will allow me to sharpen my chisel and plane blades regardless of its's length. ie... What jig clamps the chisel the lowest down? Normally once a chisel get down to a certain shortness, most jigs can't clamp it with putting a steep angle on it. It would...

I have a Scheppach Plana 3.0 Planer & Thicknesser Combination, bought in 2006. The rubber rollers need replacing... (the feeder drive's feeding pressure is messed up),. It's as if the rollers aren't pushing down with an enough force. I think it best just to buy new rollers as well as fix the...

Hi, I am wondering what's the best router table lift out there? I have been looking at this one... UJK Router Elevator Are there any types without the chains as I have read that they get clogged? Does anyone have experience of router lifts with this why of operating... ie... the chain. Is...

What type of router device/model/configuration would folks suggest for routing out door striker plates? etc... I'm guessing the smaller the better so it can be used free hand but also with the most power possible for the job? I would mostly be routing out 2-3 mm depths.... but would also be...

I want to use a secondary filter material to save my filter on my Shop Vac. Like the material that is used in the smaller vacs, when bags will take up too much of the already limited space in a little drum. These tend to be placed over the top of the drum/bin section and then the top/lid/filter...

I'm in need of a bushing for the "Bosch POF 1200 AE" router... but not the one that comes with it. One that is suited to dust extraction... ie Large holes in it to allow dust and chips through into the extraction attachment. At the moment the one on the router is a solid plate. I've search...

Hi, I'm looking for something that is light, as small as possible and can be mounted to a seat or bench,.. but is an extendable/retractable pole. Something that I can attach a shop vac extraction hose to, so that the hose can be held at shoulder height, rather than dangling down on to the...

I have been searching for something along the lines of a "electric/small/portable air compressor". But everything I'm seeing on the internet has car battery clips on it. I would need something with a wall plug on it, so I can plug it into the my van inverter and at the end of the day and blow...

Hi, I am looking for a small light "portable" dust/wood chip extractor... but with plenty of power/suction. I don't mind having to empty it out often due to its small size, (end of day/every other day)... but I want something to fit under my seat as I chip outdoors for hardware. Then when I'm...

I am looking to buy an air pump/wedge. I fit hardware on doors, handles, etc... and will mostly need it to hold doors and cavity sliders. Occasionally I will need it for removing doors, so would want a heavy duty one for sure. What experience do people have with air wedges and what would they...

I have a (HVLP) Extractor which, I've read, aren't good for fine dust. I was thinking of using it in a down draft table, table saw, router table "All in One" table. With the (HVLP) Extractor as the main suction. I'll probably add a shop vac in there too, but want to find out if a cyclone +...