Search results

Your answer is here: https://www.wood-database.com/wood-filter/ You'll just need to do a bit of simple maths Duncan

In brief: Vacuum generators require an air compressor to be running. Noisy, and can use a lot of electricity but should be able to generate near enough 100% vacuum, not that that is necessary or always desirable for a vacuum chuck. Rotary vane vacuum pumps are generally quiet and small and...

As well as not holding the chuck, he was feeding the drill in by sliding the tailstock, rather than by using the handwheel. If the tailstock is free to slide, it's also free to wobble which may have loosened the arbor. He also drilled in a long way before withdrawing the tailstock to clear the...

Do as is commonly found on window blind brackets. One vertical elongated hole and one horizontal elongated hole. At a guess I'd say the holes are about twice as long as they are wide. Duncan

https://www.ukworkshop.co.uk/threads/uk-ireland-timber-yards-please-add-your-favourites.108370/unread

The Faithfull set is a poorly chosen set in my view. Two scrapers, two spindle roughing gouges, and two skew chisels (one of each is adequate to start off) but no bowl gouges. Phil's five, above, is good; perhaps plus a scraper and you'll be in a position to try most things. Duncan

Buy one hose from Charnwood (cheaper than Record Power), cut in half, attach to Camvac, put socks over the ends, and direct away from work area Duncan

Andy Harrison in Burton Latimer was always very obliging when I went to his place. His website looks somewhat moribund but it can do no harm to contact him. http://aharrisonwoodturning.co.uk/ Duncan

The diamond belt does look rather thick but, if it's not touching the tool platform as suggested above, I'd try adjusting the belt tension with the eccentric adjuster right at the top centre of your picture. If it is touching, I'd put shims under the tool platform before grinding the platform...

A lovely and generous offer, although not of interest to me. Good on yer! Duncan

Would this help with your dilemma? https://www.classichandtools.com/sterling-tool-works-combination-rules-metric/p1594 Duncan

Good quality circlip pliers are vastly superior to cheap ones so get Knipex or similar if you're struggling with poor quality ones. Duncan

Mark Hancock is in the USA - a long way to go!

Must confess, I hadn't thought of using a pin chuck but perhaps that's because my usual drlil chuck for lathe use goes down to 1mm so the issue only arises on those rare occasions that I want to use a 1mm drill in my pillar drill. The pillar drill chuck only goes down to 3mm. A minor annoyance...

If you plump for a 16mm chuck make sure it will hold a 1mm drill bit. Some only go down to 3mm, which is annoying at times. Chronos or RDG are good for such things. Duncan

These any good? https://shop4fasteners.co.uk/fasteners/socket-screws/socket-capscrews/socket-cap-screws-metric-stainless-a2.html https://shop4fasteners.co.uk/fasteners/socket-screws/socket-capscrews/socket-cap-screws-fully-threaded-self-colour.html Duncan

As per Bushwhacker, buy or make a drill drift. Lower the drill until the slot in the quill is exposed, insert drift until it contacts the top of the chuck Arbor, hold the chuck in your hand, and give the drift a smart whack with a hammer. The chuck and Arbor will drop into your hand

Depends on the size of wood that you are cutting. Most 14" bandsaws would do the job for you I would imagine, but second hand is the way to go and bigger is always better...

I know nothing about this sort of work, but would a basic bandsaw speed up those joints. Needn't cost much and could be sold on if no longer required.

Look him up on YouTube - he makes a living working very fast, very accurately, with minimum tool changes. He really is extraordinarily good