Search results

UKworkshop.co.uk

Help Support UKworkshop.co.uk:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. T

    How not to drill a pen blank or turning your jacobs chuck into a hammer!

    Those safety glasses wouldn't have been much use if that chuck had hit him in the teeth! cheers Andrew
  2. T

    Looking for old, wide board of true mahogany

    https://www.forestguitarsupplies.com/236-1-piece There you go. Should be something for you there. It`s all finished to 45 mm thick (which is what you want if your'e doing a 59 burst with a maple top. Unfortunately because of brexit it's going to be more expensive. Cheers Andrew
  3. T

    Looking for old, wide board of true mahogany

    1.75" should do you if your doing a burst. If your doing a 1954 all mahogany then you'l want another 15-16 on top of that. Did you ask on the Mylespaul forum? Cheers Andrew
  4. T

    What connector is this?

    The crappy moulded 100mm down to 60mm or whatever it's supposed to be reducer is an absolute piece of junk(doesn't fit without heating it) record have come up with a new connector on the camvacs but won't supply it to existing camvac owners who want to upgrade (I can't see any reason why not as...
  5. T

    Rutlands one hand clamps marking wood

    Thanks for all the replies. I managed to get the marks out by rubbing with a cloth with some Methylenchlorid - Dicchlormethane (thats the German name for it on the bottle. It's used for model plastic kits as glue) A quick rub and the marks have gone. I hope it helps?? I sent Rutlands a message...
  6. T

    Rutlands one hand clamps marking wood

    I have just clamped up some Honduras Mahogany with some Rutlands one hand clamps that I bought a few years ago (red plastic sides with a black kind of rubber material on the faces) and the clamps are leaving what seems to be an oily mark on the wood. Has any one had any similar experiences with...
  7. T

    Rip off Britain?

    I've got a Vaillant boiler the last repair from Vaillant cost about €300 for a circuit board. There was a popped electrolytic cap with a bulging top (chinese?) Unfortunatly I wasn't home when the service guy came I would have fixed it myself. But by law here in Austria they are not allowed to...
  8. T

    It never happens in Europe!

    I wonder if one would consider the recent batch of politicians as natural disasters?? Cheers Andrew
  9. T

    It never happens in Europe!

    They might be very sensible, just try walking up an icy slope with them!! The icy slope definitely wont tolerate you!! Cheers Andrew
  10. T

    It never happens in Europe!

    I live in Austria and in general snow is not a problem. A few weeks ago there was a good snowfall of very wet snow which brought down a lot of trees and especially branches because of the heavy weight, including the top half of our neighbours pine tree. The authorities here were a little slow to...
  11. T

    2mm diameter drill bit bends?

    I use a hardened map pin or scribber point. Cheers Andrew
  12. T

    37mm hole?

    Yes use wd40 and go slow, otherwise it will melt and grab. I you go with the router keep the speed low and feed rate high with a bit designed for acrylic and you`ll have to use several passes. I would take it to a laser cutting shop and get them to do it. Cheers Andrew
  13. T

    2mm diameter drill bit bends?

    As a retired guitar maker I can recommend these Proxxon 6 Piece HSS Twist Drill Set 476782 Drilling side dots is what I bought them for and they work fine. Just make sure the fb's /neck is fixed down on the drill press and you don't have a lot of run out on your drill. Clear the drill...
  14. T

    Wet & Dry Sandpaper

    Starcke Matador Wasserfestes Schleifpapier If you can get it in the UK. It's the best i've used over 50 years and it goes up to 7000 grit Cheers Andrew
  15. T

    Yet another wood ID

    A Zebra without stripes? I don't think so. Cheers Andrew
  16. T

    Yet another wood ID

    IROKO ? Cheers Andrew
  17. T

    Wood ID

    https://www.wood-database.com/utile/
  18. T

    Dremel clone adaptor?

    It's on sale at a discount $59,99 at the moment, still 6 in stock Cheers Andrew
  19. T

    Dremel clone adaptor?

    These guys usually have it in stock StewMac Precision Router Base Shame Britain left the EU as you would have saved the vat . Veritas does this Veritas Complete Set, Plunge Base for Rotary Tools | Routing | Dictum not cheap!! there's probably a chinese knockoff on Aliwhatever! Cheers Andrew
  20. T

    Which one 352 or 352s

    Go with the 352s it's got better guides. I've had a 352 (the green one in the photo) for over 40 years. It's done sterling service and needed little maintenance. But it is underpowered for it's size which is a shame. After screwing up trying to resaw a thick piece of curly maple I bit the...
Back
Top