Search results

My battery charger for my golf trolley has stopped working (no power light showing. checked fuse.) I am in the Canary Islands (Fuerteventura) so no chance of getting a replacement soon. It is - Input AC100 - 240V, 50/60 Hz 1.0A Output DC 14.4V ---3.3A This means not a lot to me. Question is -...

Can anyone send me a link to some good feet please. All the reviews of the ones on Amazon I’ve seen are saying hard rubber/plastic?

I am making a chopping board as a wedding present for a friend. I want to get it engraved with their names and the wedding date . I'm near Nottingham. Any recommendations? TIA

I want to make a floor mounted cupboard for some of my tools and to stand another cupboard on top of. I'm thinking 1000 wide by 900 high by 400 deep. Two rows of 200 x 150 drawers at top and then the bottom area divided into six areas with doors on. Anyone got any plans for something similar...

I haven't used a router much and I am getting some scorch marks when putting a round over on some hard wood (Beech I thinK?) I am using a trim router. It's a new bit so should be sharp. How do I avoid this? Is speed too high? TIA

I find myself needing a couple of wood files, maybe three. Coarse, medium, fine. Any recommendations? TIA

I am thinking about building something like this garden room. Dimensions are not critical but just thinking of OSB board sizes. I watched a video of a guy who does it commercially and he uses many threaded bars concreted into ground with a foot plate which the frame then sits in. Is there a...

I want to build a chest with different size drawer to store my tools and stuff in. Below is an idea of what I'm thinking. About 300mm deep. I've never attempted anything like this so my thought process is to do the rebates on the sides as one piece and then split. Question - Would the uprights...

Adjusting table saw - The blade on my saw appears slightly out of alignment with the mitre slot and fence. How do I adjust this please? Scheppach 105s

Please don't ask how but the bracket my riving knife attaches to has broken off. It forms part of the whole motor housing. It is a cast item. Is there any "adhesive that would safely put this back together - epoxy cement type stuff. Also in second photo is the "sliders" in my saw. It seems odd...

My Shop was built as a prefab garage with an up and over door. There is a gap at the bottom of the door which I was thinking of sealing with expanding foam, then trimming off excess so I can still open it. Would this work? or would it stick? TIA

Got my system in and mitre saw, table saw adaptors are good but need a one to link Bosch Orbital 18 to flexi hose. The sander has a filter box attached to it which isn't great. Th exhaust on the sander is 28mm ext (so need 28mm internal) and something 36mm at other end to fit into 40mm waste...

A couple of weeks ago I purchased one of these for £29.99 to hook up to a dust extraction system I am making. It has a blow feature by fixing the hose to the exhaust port. So I thought get an extra hose fit to exhaust port and vent to outside. Then build a little housing to dull noise of...

I made a small footstool frame and my wife is doing to upholster it but looking for the foam on e-bay, Amazon it is very expensive 550 X 350 X 100 is over £20. That's more than the wood cost. Anyone know of a supplier?

20 years ago I had a prefabricated garage built as couldn't afford a brick one. It had no guttering as not linked to drainage. Consequently the rain would run off roof and eventually find it's way between the base and wall onto the floor. The ground level at the back was also 18" higher so got...

Saw this on FB and thought I'd share. Anyone tried it? Clamps in both directions

I just bought a wet & dry vac from Lidl £30. Only came with one bag. Are the bags fairly generic? Could I use it for sawdust etc without the bag and just empty into bin? Vacuuming has never been in my area of expertise!

Greetings, I am trying to build a selection of pockets screws sizes but only want max 100 0f each. Got 1", 1 1/4, 1 1/2 but cant find 2" or 2 /12 in this quantity. Not precious about them being Kreg. Used Triton and found OK. Triton website not easy to navigate. TIA

I would like to make a chopping board but every video I have watched uses a planer/thicknesser to level things up. How can I achieve a good finish without one of these? I don't think my planing skills could manage it? I would imagine a ROS would take forever on hard wood? Can you hire them? TIA

I need to make a zero clearance plate for my table saw but don't know what material to use- thin enough and strong enough. Any advice please? TIA, Robbo