Search results

UKworkshop.co.uk

Help Support UKworkshop.co.uk:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. N

    Elektra Beckum KGS331 sticky blade guard.

    While mucking about trying to set up the blade, I was rather annoyed with the blade guard binding. Took the blade off and operated the guard. It seemed to be sticking on the plastic lever where the metal locking catch sits between two positioning guides. The guides were a little proud, so...
  2. N

    Lost thread for Elektra Beckum KGS331

    Hi Mike. Yes I've done all that but the threads that come up on the list do not contain the bit I'm looking for. Cheers, Geoff.
  3. N

    Lost thread for Elektra Beckum KGS331

    There is a thread spmewhere, which I started, about the adjustment of the above for squaring up to the blade. Unfortunately I can't find it anywhere not even in my messages I'm supposed to have put up. Mind, when I try to cut and paste, everything ends up in the ether. I'm looking for a reply...
  4. N

    Accessories for Elektra Beckum KGS 331.

    Thanks all. The slots I was talking about are in the fence. Looking at the brochure, it would appear they are for the supplementary fence. It already came with the stand, dust extractor, work clamp and positioning laser. The only thing I can see that wood be useful is the length stop. Scholar...
  5. N

    Accessories for Elektra Beckum KGS 331.

    I've had my saw a few months now and am very happy with it apart from still not getting it absolutely accurate for cutting mitres to match up. I've spent a lot of time on it and gone through quite a bit of scrap wood which is even more scrappy now. However, I'll get there. What I would like to...
  6. N

    Rage and Incra

    Well, it's been did and tested. Not 100% happy but is very acceptable. The bolt I fitted will have to be changed for a small grub screw, but that's all. I must admit I think I might have been better off with a good quality sliding mitre saw But the table saw is a bit more versatile. Regards to...
  7. N

    Rage and Incra

    I've come up with an idea. There is an "in house" sled on the table. So if that is running true, I can lock the mitre bar to its slot and use that. I was watching a utube somewhere which was saying about the blade maybe not parallel. So first things first, give it a check. Got my DTI and...
  8. N

    Rage and Incra

    Hi all, Thanks for the replies. Robbo what or who is WWMM? I've been doing a bit of searching and found these 'ere adjustable slides. Great, but the dimensions seem to be for a 9.5mm deep slot. I measured the slot on the Rage (or rather the thickness of the T bar) and found it to be 7.5mm. As...
  9. N

    Rage and Incra

    Hi all, I bought an Evolution Rage 5-S table saw about 18 months ago. Mainly to make picture frames. Unfortunately I do not have much success due to the inaccuracy of the mitre slide bar. I set everything up using a set square, but obviously the slackness in the mitre slide means inexact cuts. I...
  10. N

    Need a bit of help.

    Hi Fezman, Thanks. I logged on to the site and registered. I put some part numbers in that I got from a users manual on line. The answer came back "no results found". I've sent an email asking why. Regards, nandesuka
  11. N

    Need a bit of help.

    Hi all, Thanks everyone for the safety advice. Mike G, I've already got a pusher stick which came with my Evolution table saw. On the safety side, I'm an ex marine then maintenance engineer. I think the most dangerous thing encountered when I was at sea was my wife who I met in Japan. I'm not...
  12. N

    Need a bit of help.

    Hi, Not only am I new to the forum, but also woodworking. However in my wisdom, I decided to make some tool boxes for all my other tools. I have lots of sockets, ratchets, extensions, files spanners , taps, dies, drills, etc.etc.. I decided to do this by recessing shaped holes in a board and...
Back
Top