Search results

Any one know where I can get hold of the below inside the UK .

The door above my weather bar has started to lift the decorative Mahogany veneer just above the bar, I feel my only choice is too extend the weather bar upwards with a pice of Mahogany, any suggestions of an alternative solution?

Anyone done this, the instructions are not helpful as it says: "Use a circular saw fitted with a sharp blade to cut concealed edges. Position the panel face up or down depending on the blade type and start all cuts into the factory finished postformed edge." So no guidance on whether to cut...

I order a fair few items per week over the internet and get tracking information sent to me, the problem is I don't know what item is being sent and the tracking information does not give me a clue, is it me or do others have the same frustration?

Been out of the loop on tools for a while, but feel I need to update my sliding mitre saw, what I need is one without a rear overhang or projection, I know about the Bosch monster, and the Makita, not looking to spend Festool monies, does anyone know of any other available options?

Hi all you turners, I am looking to raise my settees by 150mm, I think Bun feet would look the most appropriate in a fairly heavy wide section, what would you recommend?

Just received an e-mail from Axminster offering a Axcaliba hand saw worth £14.00 free if you spend £40.00 in store, use code EFLASH.

Just been sent this link: https://www.ukhs.tv/POWERPLUS-115mm-Dua ... 4517620052 except for the issue of a wider kerf and build quality what issues/benefits would this have.

This looks very convenient everything in one case so I bought it: https://www.tooled-up.com/makita-227-pi ... Newsletter and not impressed by the quality, its not Chrome Vanadium, feels very soft to the touch, don't think it will stand up to any hard use, only time will tell.

I need a metal tool chest and wondered if anyone here has one of these they can comment on: https://www.robertdyas.co.uk/hilka-14-d ... wE#reviews seem inexpensive and has good reviews, only thing missing from it is drawer liners, but they can be sourced. Mike

Anyone any recommendations for the above, seem to be available at bargain price's, but would appreciate some feedback from those that own one. Mike

Just in case anyone miss's this, today only?: https://www.rutlands.co.uk/sp+power-too ... nds+dk2079

I need to remove a large area of rendering and looking for a lightweight SDS type drill/chisel to accomplish this, lightweight because I will be up a scaffolding, preferably something that has a good method of dampening the vibration (Arthritic hands) so far its down to these two...

Just had an e-mail from Record Power, they are offering deals at the : https://www.thetoolshow.com/ Kempton Park race course show from 12-14 October 2018. Mike Sorry if this is in the wrong place, could not find any other suitable place with a search.

I need some Oak Constructional Veneer to wrap up the side of a very torturously shaped handrail, I need to build this up to approximately 7mm thick so need 2mm or somewhere near that, anyone any recommendations of where to source this. Mike

As per the Subject heading, I have found this one : https://www.amazon.co.uk/KREG-KMA3200-S ... B005FKX6D8 looks reasonable and is a Kreg so expect fair quality, anyone have any experience without paying Veritas type costs: https://www.axminster.co.uk/veritas-she ... jig-474283 Mike

Any of you guys know anything about speed controllers, I need to slow down a 5amp 1Hp pump which currently (sic) runs at 2850 rpm, I would like to slow it down to 900rpm and run longer, any recommendations? Looking at this one: http://vi.raptor.ebaydesc.com/ws/eBayIS ... 5000&ver=0 Mike

I am looking for a 12mm approximately diameter sharp pointed round over router bit, unfortunately Wealdons are 2mm not pointed, I have found one on e-bay, but at £6.50 with a 1/2" shank I'm a bit worried about quality, anyone have a recommendation? Mike

How do you guys cut cove sections of about 75 : 100mm width? I'v seen the Rockler cove cutting jig and thought I may make something similar, what do others think? Link: http://www.thisoldworkshop.com/index.ph ... le-saw-jig Mike

As the title I am looking for a Makita min cutter, but the complete kit, at the moment all I can find is bare units, batteries and chargers, surly there must be complete units available somewhere, perhaps at a saving? Mike