Search results

I can supply you with cmt Orange or stehle bot are very good quality knives if you let me know the size and qty fitted I can send you a exact price

Being a small 10" machine I'm assuming it's single phase. If this is the case a a over tightened belt will make struggle to start due to the low torque from the motor. Having said that I would remove the belt completely and ensure everything is free running I.e the spindle I would then start it...

I haven't uploaded that page yet as I'm currently working on it

Thank you The tool shop is in addition to the engineering service I have been offering for 5 yrs now. Before that I was a service engineer with wadkin Most of the tooling I sell at the moment is to my existing service customer base but I would like to expand the tooling side as I can't really...

Ok This morning I have gone through with my good wife and spell checked the entire site. As for shop content what items would you guys like so see added next. At the moment I intend to list the remainder of the 40mm euro knives (about 100 to go) and the add the 50mm euro cutters (around...

Thank you both I will have look at the spelling and grammar tomorrow. feedback is important to me whether it's good bad or indifferent

Hi Guys Im not sure if Im allowed to post this on here so I apologise in advance if I'm breaking the forum rules. I just wanted to announce our new online tooling shop at http://www.tjwoodms.co.uk/ourshop/ At the moment there are roughly 1800 items online with a further 13000 is to add over...

the baos is just about the best machine of that size ever built the only real weakness it the feed gearbox can go but the parts are still availiable at reasonable prices also i have seen a couple that have managed to shear the feed motor shaft both of these problems require the machine to be...

the last brake i fitted came direct from dold and cost around £250. Fairly easy to fit you may be better off going for a new starter and brake as i have had problems in the past with the combo of new and old switch gear. Make sure you fit it on a wel it on protected area of the machine as i have...

Many of the prisons have joinery shops for prisoner rehablititation. the machines are usually well cared for and not worked very hard. they are also fully serviced every six months it used to be done by wadkin before they went pop. Im not sure who looks after the contract now. I used to find it...

the wadkin BTS 500/630 had a mechanical counter that was accurate as well as powered rise/fall you can get a good one for between 3-4k. These are far stronger than the robland. And give a really good finish. but if you want the didital read out it narrows your options as not many manufacturers...

The robland machines are a decent machine for the money certainly no better or worse than scm/griggio but not as good as a wadkin/dominion. Yes the panel saws do go out of square but its easy to re-adjust. one of roblands weak points is the switch gear seems to be a bit fragile (if you have...

Its difficult to say without seeing whats going on. A common problem i come accross on thicknessers is operators tend to increase the spring preasure when they are having problems feeding which causes more friction in the bed and makes it harder to feed the machine. Try backing off the preasure...

olly what you have failed to take into account is a wadkin BEM that you used has likely 30yrs ish of heavy use and still going strong the felder will not last anywhere near that length of time. for example most good old fassioned heavy cast machines will will run for 20/30 yrs before they...

theres mjm in bristol and also appleford one of these guys im told has retired but im not sure which one. I have seen quite a few mjm sold machines around ive not seen a bad one yet. Not so many appleford machines.

sedgwick no shadow of doubt there the felder may look pretty but its not very robust and there is a lot of cheep and nasty colourfull plastic covers that are easy to damage the spindle the spindle unit itself is really weedy. I have aslo seen problems with warped fences. The sedgwick may...

Had a look at the wadkin combi today it turns out its a dim saw spindle combo. The saw blade can be wound left and right but the bushs are shot as is the winding nut and screw should have replacements made for the new year. there has been a bodge job done on the original parts to hold the nut...

the wadkin name is still going now owned by daltons for the cassical machinery but i from what i hear they have sold very few if any new machines since that aquired the rites ams own the rites to the grinders and moulders but as far as i know have no plans fro production

Thanks Bob so with a 1.5hp motor as a rule of thumb a 50-60uf should do the job nicely I havnt come across the 30-40 basic rule before thats usfull information thankyou

im not sure how the system works from what i hear its a one off. but there are quite a few wadkin one offs out there most of them were built as prototypes and never made it to production. I will have to investigate it further when i strip it down on wed im looking at a wadkin combi...