Quantcast

Search results

UKworkshop.co.uk

Help Support UKworkshop.co.uk:

  1. jasonB

    How do I make this?

    No problems whan I have done layon strips
  2. jasonB

    Veneered Suppliers

    I think Travis list a 3mm birch ply but its only a C grade face As for the decorative veneers the only way you will get close to 3mm is to take a sheet of 1.5mm birch skinply and veneer each side with the pre jointed "flexiveneer" which would bring you close to 3mm overall
  3. jasonB

    How do I make this?

    Stuart PM'd me about this but I thought I would reply here as it may be useful to others. For the doors I would go with 22mm MRMDF styles and rails and a 9mm panel, 18 & 6 is OK on kitchen doors but feels a bit flimsy on taller wardrobe doors. Method as above groove 10-12mm deep. The same...
  4. jasonB

    wardrobe hinge help needed.

    Blum do one of the integral Blumotion consealed hinges specifically for thicker doors which is 95 degree opening lay-on doors 71B9550 Inset doors 71B9750 I usually go with the 173H710N mounting plates for these, assuming 18mm carcase EDIT pages 26 & 27 has details...
  5. jasonB

    Thoughts on an Emco lathe please

    I had the slightly older geared head version for a number of years the Emcomat8.6 and was very happy with it. Far better build quality than teh imported far eastern machines. Parts are still available but like teh Emco accesories are not the cheapest, Pro Machine tools do them...
  6. jasonB

    4wd help

    Windup or an automatic locking front hub playing up, had that on my old diahatsu.
  7. jasonB

    Sourcing Vinyl for vacuum bag

    I've used the 500 and 1500 wide stuff and just sealed with parcel tape, on the 500mm one I use the seal from my bagpress but easily made from minitrunking and a rod. Its quite durable you can get quite a few uses from it as long as you are careful putting work in so the corners don't snag.
  8. jasonB

    Lathe boring tools

    Really depends on the job and size of hole. For very small stuff I use old HSS slotdrills ground to a suitable shape for boring ( you can also use them as is in the toolpost) For general boring I prefer the indexables on all metals changing the tip to suit For large boring jobs particularly...
  9. jasonB

    Options for MDF Wardrobe doors?

    22/9 will be fine. MR MDF though you could go with a lighter board for the panel as the edges won't be exposed as they tend to be fluffier. Panels do want to be glued in
  10. jasonB

    Options for MDF Wardrobe doors?

    I also use loose tennons but prefer to use 22mm styles and rails with a 9mm panel, the thinner option is OK on smaller say kitchen doors but feels a bit flimsy on a full height door. Add a panel moulding around the recess if the client wants something a bit more than plain shaker.
  11. jasonB

    Danish Oil leaves orange tone

    Is it a fresh tin? old stuff can discolour as well as settle out. J
  12. jasonB

    Indexable lathe turning tools

    No CCGT C = Rhombic Shape, C = 7degree Relief, G = Higher Tollerance due to ground edges, T = Single sides CSK hole Although they are known as CCGT that really does not describe the differences very well apart from the G, you really need to look at the makers individual codes at the end of the...
  13. jasonB

    Indexable lathe turning tools

    For thise that have a job getting a fine finish with the indexable tips try one of the tips for Non-ferrous metals such as CCGT rather than the general purpose CCMT. these are far sharper so don't tend to push the work away on a light lathe or slender part. Did this crank in EN8 a couple of...
  14. jasonB

    Looking for rip blades with flat teeth

    The small Kity machines were supplied with a flat tooth blade as standard, worth asking at NMA if the spare is the same http://www.nmatools.co.uk/productdetail ... roduct=846 The Freud LM01 0400 is another option but not many selling it unless you want to try russia
  15. jasonB

    Bathroom Panneling

    I've done several with MRMDF and just routed Vees in it, also used the ready made sheets of beaded MRMDF both easy to paint and no caracking of teh paint at teh joints. Good quality softwood also looks good but get it inside to aclimatise and make sure you get a couple of coats on te back before...
  16. jasonB

    Sawmills in the Weald area of Kent

    Maybe a bit too far north but I have used these two http://www.scottimber.co.uk/ http://www.treespanner.co.uk/
  17. jasonB

    Machining Aluminium with end mills.

    You will get a more accurate slot with a 2-flute slot drill rather than an end mill which tend to cut oversize in this situation. Failing that use a smaller cutter and work upto the width. It will also clear the chips better at higher revs
  18. jasonB

    Plywood grade with knots, figuring etc

    Have you thought about buying a more figured birch veneer and sticking that to a standard sheet, most of the veneer suppliers do "figured" birch in crown and rotary cuts. Masur birch would give you some nice figuring too. J
  19. jasonB

    Help with a fitting

    Sounds like a "taper connector" Isaac lord used to do them but I can't see them on their sitenow as did Woodfit but they have gone bust, Rockler in the states do them or you may be able to google them and while you are ther have a look at teh knock down bed fittings which may suit your 5x1 rails J
  20. jasonB

    Drill Bits

    Slow spirals can be used on Copper, brass, bronze and plastics as they are less likely to grab the work
Top