Quantcast

Search results

UKworkshop.co.uk

Help Support UKworkshop.co.uk:

  1. C

    Boo Hoo

    Surprised nobody has mentioned this....http://www.finewoodworking.com/item/20355/new-yankee-workshop-series-ends
  2. C

    My French Workshop - WIP

    I'm in the process of organising my workshop in France. It's approx 40m2 built of blocks with a water-tight tiled roof. I've insulated the floor and laid a chipboad floor on a 3x2 frame work. Plans are to install a "ceiling" and create a timber store above, I'd like to insulate and board the...
  3. C

    Push To Open Hardware

    Don't know if any of you cabinet makers can help. Have a client who wants handle less doors with a push to open feature. I see you can get push to open hinges as well as catches. Do you actually need both the catches AND the hinges or can you just fit the catches as the doors are just going...
  4. C

    I've just bought this.....

    Since trying to chop my fingers off on the table saw https://www.ukworkshop.co.uk/forums/viewtopic.php?t=19891&highlight= , I've had a little time on my hands (no pun intended :D ) so I started browsing French property sites and came across an old cabinet makers workshop which is approx 175m2...
  5. C

    Still got 10 fingers..........JUST (Parental Advisory)

    I had a major kickback while ripping a piece of oak on Thursday the result of which can be seen in the attached images. [/img]
  6. C

    Customer Service....Brilliant

    I finally opted to go for the EZ saw guide system from Eurekazone having watched it's development over that last couple of years. I had a project that involved cutting a load of melamine faced MDF and I already had 3 CSs so wasn't about to splash out on a Festool system. Anyway, I slightly...
  7. C

    Somebody got a bargain.......

    possibly??? Woodrat WR5 £200 on fleabay.http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&ih=014&sspagename=STRK%3AMEDW%3AIT&viewitem=&item=330118171164&rd=1&rd=1
  8. C

    Eurekazone "Bridge"

    I've just ordered the EZ system and while investigating same came across this from the guys at Eurekazone. Looks pretty useful. http://www.youtube.com/watch?v=OZScA15bl-A&mode=related&search= http://www.youtube.com/watch?v=SKmIxFNhIN8&NR=1
  9. C

    Barter

    I've got a little used Leigh D4 dovetail jig with all the bits & bobs that go with it. Before I put it on ebay, I thought it might be worth seeing if anybody on the forum would be interested in "swapping" it for a lathe. Ideally, I'm looking for something with a swiveling headstock and...
  10. C

    Veritas System 32

    Has anybody had any experience with the Veritas System 32 cabinet system? Cheers Col
  11. C

    The most accurate tablesaw fence going for a song.....

    http://cgi.ebay.co.uk/INCRA-JIG-SAW-BENCH_W0QQitemZ130037580846QQihZ003QQcategoryZ11705QQssPageNameZWDVWQQrdZ1QQcmdZViewItem
  12. C

    Sliding Table

    I have a sliding table that will fit the SIP and SIP derivatives such as the FOX, ITECH etc. I bought it as part of the saw but it's just too big for the workshop. If anybody is interested, then I'd be prepared to swap it for a cast extension table (which you have to remove to fit the sliding...
  13. C

    Site Saws

    I've just had to fit out a dressing room building cabinets and dressing table out of MFC - (yes I know it's not proper wood but that's what the client wanted) I wasn't able to transport my table saw to site so all cutting was done using my trusty Skill circular saw which was a real...
  14. C

    Hardwood Worktops

    I've got my first hardwood worktop to fit coupled with a belfast sink. My question is, once I've made the cutout round the sink, what is the best treatment for the edges - should it be some sort of oil such as danish oil or good old polyurethane? Col
  15. C

    Cutting Worktops

    I'm starting to mitre more and more laminate worktops and I have a number of queries that I hope some of you guys and gals can answer. I use a Freud FT2000VCE coupled with Freud 1/2" straight cutters of the appropriate length. My experiences have been varied although the end result has been...
  16. C

    Cutting Edge Woodworker

    Has anybody been watching this new offering on H&L? Paul Bradburn produces some nice pieces however, I find the filming soooooo infuriating. The camera seems to focus more on his face than what he's doing with his hands. I'm not saying there's anything wrong with his face, it's just that I'm...
  17. C

    Board Edging Trimmer

    I have some MFC panels to edge and will be using Melamine edging. Can anybody help me locate the little handheld tool for trimming the edges once the edgig strip is applied. I've seen Norm using one and this new guy from "Cutting Edge Woodworking". It looks like it is a device that has a...
  18. C

    Bargain

    Just bought an air nailer/stapler from B&Q at the bargain price of £36.72 I'm not sure whether it was wrongly priced or not!!
Top