Recent content by Superchippy123

UKworkshop.co.uk

Help Support UKworkshop.co.uk:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. S

    Which bandsaw do I get - Axminster AC1950B or Record Power 250 or something else entirely?

    Havnt had a small bandsaw similar to the one's you've mentioned i would 100 percent save your money for a bigger bandsaw. Have a record power bs350 now and i love it for resawing and ripping boards. Got it 2nd hand for €550 so not far off the top end of your budget
  2. S

    Axminster ts250m fence

    But looking at it there now i dont know will my fence with that
  3. S

    Axminster ts250m fence

    Ya iv been looking at that and was wondering would it fit. Iv even looked at some of the trade range models and see could i order parts for that and try make it fit. Just dont want to waste money on the thing if it dont fit. Il send an email and see if the upgraded craft 250 model would fit my...
  4. S

    Axminster ts250m fence

    Ya thats looks what im looking for id say. Did it take much to modify it to your table saw. Appreciate the reply.
  5. S

    Axminster ts250m fence

    Ya seen that incra table looks some job to be fair but wayyyy over the budget😂😂. Ya good idea about moving the whole fence maybe. Ya the left hand side just gathers tools on the table only😂😂.
  6. S

    Axminster ts250m fence

    I think your misunderstanding what im looking to do or maybe i havn't explained myself properly Im looking to increase the rip capacity of the saw not increase the length of the fence itself. Currently it will only rip to 450mm i want to increase the capacity to somewhere near 600mm. Regards...
  7. S

    Axminster ts250m fence

    Y Thanks for the reply. You wouldnt have any pictures of your set up to hand would you?? I just cant picture it. Is it lengths of steel either side or alluminium?? Sounnd
  8. S

    Axminster ts250m fence

    Cheers for the reply. Ya its annoying really nice quiet saw and the thought of going back to dewalt brushed motor is painfull. Wh creations on youtube bought his only 2 years ago so nowhere the ten years they state.
  9. S

    Axminster ts250m fence

    Hello fellow woodworkers Quick one for ye axminster ts250 owners anyone. Recently acquired this table after using a dewalt site saw for a few years. Induction motor and cast iron table sold me on it. But iv come to think il be going back to dewalt as axmister dont sell the extension anymore or...
  10. S

    Axminster TS250-2 modifications.

    Vacuum cleaner lvhp. Might have to upgrade im not sure.
  11. S

    Axminster TS250-2 modifications.

    Thanks again lads. I have a lidl extractor which im planning to use for the underneath and a scheppach one the blade guard extraction. But i dont know will the lidl one be up to the job. Going to try and build some form of tunnel underneath the saw to force it into the ectractor like has been...
  12. S

    Axminster TS250-2 modifications.

    One more thing lads. Is there parts missing of this piece in your opinions it seems wicked loose whenblade is at full height? As in should there be clamps on the bar holding the threaded rod
  13. S

    Axminster TS250-2 modifications.

    Thanks for the replies lads. Im most concerned about dust really getting into the motor like you've mentioned mike. I think the previous owner cut this shroud off. Would port underneath without the shroud do much on its own in your opinion mike. Iv made an overhead attachment allready but the...
  14. S

    Axminster TS250-2 modifications.

    Well 1st time poster on this site but have been reading on here with years with some great info on here. Just purchased a used ts250m but it seems to be missing the dust shroud underneath the saw that keeps the dust away from the motor. Can anyone who owns this model post a picture of it as i...
Back
Top