Recent content by NosamLuap

Lots of good advice already. The only thing I can add is to ask how you're measuring the line? You might get better results by NOT using a tape measure - e.g. if you want several pieces 'the same length' of 300mm, is it more important that each one is 300mm, or is it more important that each one...

Great post, very detailed and informative! On your last point (fig. 3.1) it would be really easy for the 3d printer file to be modified to accommodate locking pins/sockets. Were the 3d printer files supplied with the kit, or did your friend model the whole thing from scratch?

I've used Tuffsaws as a hobbyist for the last couple of years - first with a Parkside (Lidl) cheap and cheerful model - which was transformed into a surprisingly capable saw with a Tuffsaws blade! Then, I bought a second hand Record Power BS250, which I fitted with a couple of Tuffsaws blades. I...

Aha, excellent! We've all been there, so focussed on 'one part' of the problem that we miss the other! :LOL:

Cut into suitable sized 'lumps', walnut turns beautifully on a lathe so could make some bowl blanks. Depending on the size of the trunk/limbs, that only requires a chainsaw to get valuable pieces to sell (or turn, if you have a lathe!). Or, as Recipio suggests, get it milled on site into usable...

Slightly confused by this... if the bolts allow the fence to move in relation to the black handle, then move the fence 'right' in relation to the handle, then when the fence is touching the blade, you'll be at (or closer) to zero on the measurement line??

The only think I can think (without going into the garage and getting mine out to rummage further!) is that the two bolts on the top of the fence, which are intended to allow you to calibrate it to 90 degrees, are both 'over to one side'? Can you loosen those and nudge the whole fence over by 4mm??

I made this video after setting up mine (though mine isn't actually the Rage5s - it's the Screwfix own R255PTS, which is pretty much identical but I don't get the left extension!). Ignoring my blatant confusion on how to read measurements, you can see that it did line up as you expect it to - I...

You have the fence extension fitted. is it the same without that, using the orange numbers? Can you loosen the 'orange' pointer on the left and move that, similar to moving the clear alignment markers?

In fact, I'm so sure that the Charnwood 812 and the Axminster AWVSL900 are the same that I suspect the manual for the Axminster is useful to you :) https://www.axminstertools.com/media/downloads/501268_manual.pdf

From Googling that model, I'd be stunned if it's NOT a 2MT tailstock - it looks very much like the current Charnwood W813, and many similar lathes (e.g. the Axminster AWVSL900). Are you sure that whatever is in your tailstock isn't using a 2MT? If you wind it all the way in, does the current...

I bought this last autumn, and whilst it's only a few months, it seems to be holding up well - bandsaw and lathe haven't noticeably rusted since applying (they were both 2nd hand, and never 'shiny' surfaces, but they've not got worse!)

I think this is the wrong way - you PUSH the fence away from you, into the saw, so that the black 'T' section is firm against the track, as you lock it down. (At least, that's what I do!!)

I have the Screwfix 'sister' saw to this - the R255 PTS - when the fence is not locked, it also can swivel slightly like that. Before clamping the lever down to lock it, I ensure I'm pushing 'back' so that it squares before locking. It certainly has a degree or two of drift as you're sliding it...

I'm also going to push your budget and recommend the Hyundai - I have the 24l 'silent' compressor, and it runs at 60-something dB, rather than the more usual 95ish dB for a regular compressor - that's a HUGE difference. I can easily hold a conversation whilst mine is running, and working from my...