Recent content by Joe Shmoe

Hi Folks. In the end, I just bought a new jig for toolstation for £40 and it had a 31mm slot. Everything went perfect and I'm really happy with my joints. Not sure why the other jig had a larger slot, but it appeared factory standard and fabricated that way. It cost £3 from a bootsale so no...

It's a Trend KWJ650, which I think is quite an old model jig. Plus a 30mm bush that came with a Trend T7ek, and the specified 12.7mm bit. Very strange. Just checked - the bush is 30mm but the gap in jig is 37mm. Guess they altered this in newer jigs? I got this cheap, used.

First time doing this. I have a jig that details using a 30mm Guide bush, which is what I'm using, but there's a 5mm gap each side as the guide run in the Jig is much larger than the bush. I'm sure I've heard this advice before but not sure... So am I supposed to keep to the right while...

Guys, Made an error. Recently got a bathroom plastered for complete house refurb. Now I realise that skim only holds 20kg/m tile weight. In order to rectify, I'm looking into screwing on backerboard as I hear they will hold 50kg/m upwards. Now, an additional problem is the bathroom is only...

Hello. Need to fit some worktops but only have an 18v DeWalt 1/4 router. Can you get a 30mm bush for this, and an appropriate router bit? I don't want to buy a 1/2 router but some info on the Web says a 1/4 won't be up to the job so bush/bits not available?

Hello. Installing new kitchen for a relative and getting to the point where the appliances will soon need fitting. Property has just had a full rewire and has a 32amp RCBO for the oven and Hob circuit, on 6mm T&E. It terminates into a hardwired cooker outlet. Said relative has already...

Hello. I'm installing a new kitchen for family member. The existing stopcock is right where a cupboard shelf will be, so I'm going to replace it. Can anyone advise on the best quality thing to use? Cant seem to find a definitive answer on the Web. I'm unsure if I should use a Pegler stopcock...

I've fitted a few sets of these Oak Veneer doors over the past couple of years, (Howdens brand) and used Osmo oil to finish. Halfway through fitting some that I got from Wickes and noticed it says not to use Oil? I don't remember previous doors from Howdens stating oil isn't suitable (and...

Renovating a Bungalow bathroom for my mum, and will be fitting a new bath or shower. The bathroom is tiny, being only 1600mm square roughly. Part of internal wall (1950s breeze block type) wasn't built square so a new bath or shower (not decided yet) won't fit nice. The old bath had a large gap...

Try to keep this short. New bungalow I have purchased, lots of mould in kitchen behind the bottom cupboards. I believe *may* be attributed to damp from cavity wall insulation - mineral wool installed almost 25 years ago. While rewiring and removing old sockets, I used camera too view into...

Hello. I've noticed that a small 6-inch section of felt around the edge of my 18yr Roof had started to lift. I haven't noticed any leaks and the rest of the roof seems good. What's the best thing to use to stick this back down and seal it? Hopefully reasonably easy and cheap, like a mastic...

This engineering brick seems awfully rough. Is this an indication that it's a cheap one?

Got a leak happening on a conservatory roof in the worst possible place for access. (marked with circle on drawing). Its a bungalow which helps, but neighbours also have a conservatory right up against it. There is no gap, they appear to have been built right up against each other at different...

I have an unopened Osmo Oil tin that I purchased and didn't use about 5/6 years ago. Do you think it's OK to use?

Forgot to add. Seen some videos where they just oil it while it's hanging, but not sure how they do underneath, nor under the hinges.