Recent content by diyphil

UKworkshop.co.uk

Help Support UKworkshop.co.uk:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. D

    Sold Axminster panel/table saw

    Hi, does it run on a 13amp or 16amp power supply?
  2. D

    Sold FTAGH - Fine Woodworking Magazines

    These have now gone.
  3. D

    Sold FTAGH - Fine Woodworking Magazines

    Hi Stephen They are all yours. I will send you a PM.
  4. D

    Sold FTAGH - Fine Woodworking Magazines

    Free To A Good Home. Fine Woodworking Magazine - Editions 153 (2002) to 242 (2014). These magazines were given to me a few years ago by a forum member and I would now like to pass them onto someone else. They are collection only from Rotherham, South Yorkshire. Phil
  5. D

    Router table plate FTAGH

    Router plate received today Pete. Thank you. It will make a good addition to my slowly growing workshop when I fit it into my workbench.
  6. D

    Router table plate FTAGH

    PM sent.
  7. D

    Workshop security

    I alarmed my garage/workshop with a Yale HSA6400 that I purchased from Screwfix 3 years ago and have been happy with it. It is no longer on sale but the Yale Premium+ (Screwfix 7338X) looks similar. I have the control box plugged into a 240v socket in the house and the alarm siren box and...
  8. D

    Slot Cutting Router Bit Advice

    Yes that is correct Trevanion. A groove for the 6mm panel. Thanks Trevanion and Phil Pascoe for your advice. I see you both recommend the same make as Peter Millard uses. I will order an arbor and groover from Wealden.
  9. D

    Slot Cutting Router Bit Advice

    Hi All I would like to build some wall hung cabinets for the garage with shaker style doors. I need a slot cutting router bit for the door build. The bit will be sitting in a Triton TRA001 router housed in a router table, so I could buy 1/4" or 8mm shank bits. I would like a good quality slot...
  10. D

    Buying Advice - Stanley Compressor From Screwfix

    Hi Novocaine I sent a query to SGS and have just had a message back to say FAD is approx 2/3 of the quoted CFM, so I have to assume that the delivery figure in the manual is in fact not the FAD figure. In this case I will have to rule out the SGS SC50H compressor. This appears to be a minefield...
  11. D

    Buying Advice - Stanley Compressor From Screwfix

    Thanks for pointing that out novocaine. I hadn't looked at the SGS manual and assumed that the 9.6CFM was not the FAD figure. It does make it look good value. Cheers.
  12. D

    Buying Advice - Stanley Compressor From Screwfix

    Thanks for your advice novocaine. I assume the SGS SC50H 9.6CFM would reduce to approx 6CFM FAD which may be getting a bit low. I did look at the SGS SC50V at 14.6CFM (approx 9CFM FAD?) for £180, but they have sold out so it is no longer available. I also now see that my choice of the Stanley is...
  13. D

    Buying Advice - Stanley Compressor From Screwfix

    Thanks for the info Porker. From my research over the last few days I realise that the CFM that most compressor manufacturers quote is the amount of air that the compressor draws in and not the amount that reaches the tool. I believe that the free air delivery (FAD) is the air that reaches the...
  14. D

    Buying Advice - Stanley Compressor From Screwfix

    Hi All Does anyone have any thoughts on the 50l, 2.5hp Stanley FCDV4G45CR006 compressor that Screwfix are currently selling for £219.99 or the Scheppach HC53DC 50l for £299.98. Stanley Compressor / Scheppach Compressor Does anyone own one of these. Are they reliable and value for money? Any...
Back
Top