Making a casement window (single glazed)

UKworkshop.co.uk

Help Support UKworkshop.co.uk:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

ColeyS1

Established Member
Joined
2 Nov 2009
Messages
4,245
Reaction score
34
I thought I'd share the process I go through of making a casement window. It's a fairly straightforward design, but might be of interest to someone who hasn't made one before.
I've tried to make the process seem as logical as possible, so hopefully might be easy to follow- fingers crossed !
I wouldn't necessarily do the stages in this order, but this, I think, should be the easier way for somebody considering making there first window.

This is the windows I'm making
ddc0c13cc6b8ceb9b57bd78fd006da5b.jpg

The joy of this job, is all the frame timbers are exactly the same size - 94x57mm.

First thing to do is make a cutting list so you can order timber and then cut out your pieces. These are the names of the window parts.
633518ab4f8503b8b0a284e6efcfa7e0.jpg


I usually allow around 100mm extra for length, so with this in mind, make a list of each part you require. As an example I've made a cutting list for the top window in the pic.

5f03bde31322bf7649b129ed4974a0cc.jpg

The windows only having single glazing, so only needs to be ex 2 inch thick.

Cut out and label the parts for your windows.
7b64e616e82d26070abb1d24b68930d3.jpg


Top and tail, and thickness the pieces to size.
69405201ea49a377e64812118b7e71b0.jpg

I've put the frame parts on the left pile to make finding them for machining easier.

Coley
 
The next stage is to take a rebate out of the frame pieces for the sash to sit in.
A spindle moulder will make light work of this- Equally a router would do exactly the same, albeit a bit slower.
With the rebate block in, set the depth of cut to 13mm
83fc9045fe9b536aae6f04c552dbbb25.jpg

Next set the height of the rebate. The sash is 45mm thick and ideally a 1.5-2mm gap to allow for a draughtstrip is good. Holding a stile then measuring 1.5-2mm is easy enough to set.
938611eaea84cfb59aaffb3f760ddfb5.jpg

Apologies in advance for saying a few obvious things- I wanted to be thorough and not miss out any steps.
If you've got any rough/damaged bits, nows a good time to lose them when you smash the rebate out.
df2b1ffc5b5d073df5a51463fef6a340.jpg

6ffd8ebcdb2643d3c4e08630cc796216.jpg

Push through all the pieces. The mullions will have to be double sided, other than that, push the head, cill and jambs through the same.
You might end up with a pile of wood that looks something like this.
42562f6078ac369f8e96c415308b4c17.jpg

Next thing to do is form the cill. In this instance the easiest way is to tilt the rebate block over to 9 degrees.
102c5cfc07c3d97ed307e0291356b154.jpg

You could achieve the same by tilting a table saw, although a spindle will give a nicer finish. Generally windows have a cill projection, so this is quite rare that I make one with a flush cill.
Now the angles set and locked in place, it's time to set the depth.
2a5579c4a98b8330f00a0a54f732253b.jpg

I like to keep a 12mm piece of mdf nearby as it's a good start for setting the depth. Just get the top of the rebate cutter flush with the mdf.
Now that's done set the height.
67adf7dbe2ed8ca9e532039440fd7775.jpg

Probably the easiest way is to take the cill timber and wind the block up, until the scriber touches the rebate you've already made.
Roller feed, turn on job done.
cf5dcf99e212974f57d34dd4e3aa3c9d.jpg

Needless to say, check everything's tight and the fence clears before considering starting the machine !

Coley
 
That's the machining stage done for now. Next is to mark out the parts ready for mortice and tenoning together.
Take a cill or a head and mark the overall width.
ae48365a0213510757c4b5ba625fa8e7.jpg

be6ce92628cafd6c06dd45a1c992383c.jpg

From that line, mark the size you have left, now you've machined a rebate.
In this instance it'll be 57 minus 13mm rebate so 44mm.
4a967a12a603ec6662623e9ee7287669.jpg

I'm struggling how to explain it, but hope that makes sense. So mark 44mm in from each end. Measure the gap between the new lines, then subtract the width of two of these ......
aaa88e7c73d6df4301f8ff88ac7babe7.jpg

Divide that number by 3, then mark out the mullions. I'm hoping this pic might explain what we're marking out.
c5ceebb2fd3820151d1aec6aab6d2ec8.jpg

Now you've got these lines on one piece of wood transfer the lines onto its mate so you've got a cill and head paired together.
941e03b0a4b20879348de6677e114ee8.jpg

To keep things straightforward, I'd square these lines right the way around each piece of timber. When it comes to making the mortice in the head and cill, you'll attack it from both sides.

I wish I could explain this stage clearer. This is why i quite often post pictures instead of writing replies- I struggle lol

Coley
 
Onto making the mortices. Wind the chisel so it lines up with the rebate.
7ebe44b0d51d12f471a73398352a24bd.jpg

Set your chisel to just over half the depth, then mortice from the rebate side
6c3495595d246ac5d58ba3804d624ea0.jpg

I haven't bothered with face side/face edge marks. So longs you keep the same bit against the fence each time, then it shouldn't matter.
Turn it over and mortice from the other side.
fbab7f9c710608432de5040f0ef83ce0.jpg

You'll notice in the pics that I haven't morticed to the lines on the outside. The horns will be cut off later, so morticing accurately to the outside lines isn't necessary.
If alls gone to plan, you'll have holes something like this.
f0e7b88414ecaae0277be4cc2e6fded7.jpg


Next stage is to form your tenons.


Coley
 
I'd say the marking out is the most challenging, it gets easier once this is out of the way.
The easiest way to mark you tenons is to take a jamb and mark the overall height on it. Then take your head/cill and trace the shoulder lines.
8f5824e7185aab260106973ef04b9122.jpg

This might seem a bit crude but it's fairly foolproof !!
One thing to bare in mind, is you need to mark your jambs out as a pair !!!!!!!!!!!!
2f15c7f4a51c80a456c3add3f3277218.jpg

If you don't, you'll end up with two left/right hand jambs- its easily done, ask me how I know !! [SMILING FACE WITH OPEN MOUTH]
If you're cutting them by hand you just need to set your mortice gauge and cut to the lines.
When it comes to using a tenoner, I first set the tenon with square shoulders to test fit.
08aa4b8536f7a86acb657641c72bda5c.jpg

Once happy with that, adjust the stepped shoulder
a7c296d47e8061ec797f9cc61fd6adc8.jpg

7f306685e25fb84191fd764bef745ab5.jpg

Having a tenoner spin this way means all spindling moulds, rebates etc, can be done before forming the tenons.
If you've cut the tenons by hand then this is irrelevant.
The tenoner can only do square shoulders (easily anyway) so they still need the 9 degree angle cutting on them.
This is a fairly easy way of marking the line required.
77612491f5f248a47d4e483b1dd80702.jpg

Simply set the compasses to the gap on the square side.
fd9cb1bf36d7df9fdd63be68ede823e6.jpg

Might be cheating, but I find it easiest to do the 9 degree cut on the chopsaw.
5d9d8f52ea3b3efba819360e4db70ed9.jpg

Set the chopsaw to trenching, tip to 9 degrees and the rest is history ;) if the calculations are right you'll end up with something like-
7f8b1430caba4188548d444d4c0a5c93.jpg


Coley
 
Tenons and mortices are done, now time to add the extra mouldings.
5e6d872bac4bdab27f2da5f574395428.jpg

Mortar grooves on outer timbers (jambs head and cill)


Drip groove on cill
5bafaa1019e08a1f9be90c7aba447d14.jpg


Drip groove in rebates where opening sash is. (Don't do the cill, just uprights and head !)
07eac156c02de5ff50ed950b3b5a979e.jpg

I like to put the rebate drip groove so it misses the hinge
d2249ab4ee688e0c5b29b33d298d56bd.jpg


The only other mould, is a small splay on the uprights. Either set this up on a spare piece of timber, or perhaps the end of the head or cill
b2c31458b69a679b1633972d7e3a856b.jpg

051436cf7acf5dde44426a0f08c69017.jpg


Splays on uprights done
2ec05517209b9d989a054a49200a51da.jpg


Coley
 
Wish you done this a few months back. My windows ended up very similar in construction but took way longer to figure out than if I'd had this post to reference. It's great to see how a professional does it, especially like the level of detail you're providing. Thanks!

Fitz.
 
mikefab":2uie3rmk said:
Great thread!
Thanks Coley I will be following this with interest. I have a strange fascination with windows!!
Cheers Mike.

Coley
 
Fitzroy":2oz3tw22 said:
Wish you done this a few months back. My windows ended up very similar in construction but took way longer to figure out than if I'd had this post to reference. It's great to see how a professional does it, especially like the level of detail you're providing. Thanks!

Fitz.
Thanks Fitz. I appreciate the comment. I was quite surprised how much work goes into making a fairly basic window.
I thought if I posted lots of pics on a single glazed version, I could skip various parts on perhaps double glazed or sliding sashes.
I'm just looking at getting it all down on paper first. I'll try and sort out the dodgy image rotations, once it's complete.

Cheers



Coley
 
Now most of the spindling works finished it's time to start fitting the joints together. If alls gone to plan your tenon should be too wide for the mortices. Cut these back so they're flush with the rebates.
f93badd52fea4e45c221be6f8f1622d2.jpg

1c98b13182b44cfd56d4c9f68e3b139a.jpg

02ace429b5d345ca8dc83aee36b6529d.jpg

Do the same to the cill end and chisel or saw off the 9 degree cill cut.
cf54e31bfd747d9a229914def6fbca02.jpg

Test the joints fit.
68afbb9cb1722415324050ee0ee1d5c3.jpg

Once you've got all your uprights inserted in a head or a cill, you can 'bone' them through by eye to check they're all in line.
ddf6434cb1e465bb3e5135446b8d705a.jpg

If you've cut the cill angle end with a chopsaw, it's something that shouldn't need any tinkering. If not adjust ease the shoulders to suit.
All the joints are now individually fitted and labeled where necessary, chuck it all together and check the overall dimensions.
f9f329368fcbc7dab5dbf1d9387f9548.jpg

Chuck it all together and check the over dimensions!!!!!!!!!!!!!!!!
Any errors in marking out, should now be obvious. Check the sizes and rescue/remake any parts that need redoing- Better to notice now, then when everything's stuck together !
Check it, go on. Measure twice, remake if necessary [WINKING FACE]
On your opening sash, it'd be nice to some draught proofing.
c0f8ed8195e3dc7c10634058ee6ec37e.jpg

I use aquamac 63 on window frames. The grooves for the draughtstrip is machined using a router- no more earth trembling machines lol.
8b3ba1297281c27311162c33a8190463.jpg

972337688f1f1c0cf677de48b902be85.jpg

Set the depth just shy of the rebate depth (around 11.5mm deepish)
5d59b9563d8e57a506722f703798571b.jpg

You'll notice in the pic the block of wood/packing fixed to the base of the router. It's the same thickness as the rebate (13mm) having this makes it almost impossible to accidently tip the router.
d3ed398ca8ce858b6fce9acd8686be76.jpg

That's all the machining done now !!
Sand up all your inside edges
ae999c264d0acc9bc975e8bf3be5e6cd.jpg

ccfa3b1c7477933622e749fa985c2fc5.jpg

Drill some holes in the head and cill for screwing the joints together.
5mm screw means a 5.5mm hole
e507c97eeec2aaf03b1f80415242e20f.jpg

I've found somewhere around 30mm screwing into the timber usually gives a good enough fixing.
6f2d45cd6b6734a7541c6386d789664d.jpg

Test screw the frame together.
350709eefa70611819e6fa8dbef5b6de.jpg

The joints should now be nice and tight and the window frame nice and flat. A small bit of twist isn't the end of the world, just be sure to get the jambs plumb when you fix it [WINKING FACE]

Coley
 
Once you're happy with how everything fits, next step is gluing It up.
Back in the day it was always cascamite for hardwoods and pva for softwood. The reality is, even if the glue failed the screws should hold everything together.
I use cascamite just because it's stood the test of time.
3e9a08d565716c62b991936dec7fad9d.jpg

e928f2212e4a0e92bd5129e11494fcc1.jpg

Put glue inside the mortice (come in from both sides if the glue brush won't reach) and also glue the area where the tenon shoulders fit.
a5952f1a420c017f42e632ecb5e9c9af.jpg

Gluing both mortice and tenon should mean that everything gets a good covering of glue.
I tend to have a few bearers on my bench and then screw the frame together flat on the bench.
a82e7ae7e237596076f2f73ebe80aeab.jpg

Now everything's screwed up tight, check the diagonals for square.
84795168189ceb117bb8e00ca023a791.jpg

If necessary stick a clamp/temporary batten across the corner until the measurements are the same.
2a9558fa24d391a965b955f72d078983.jpg

Clean off any excess glue with a sharp chisel or a rag
4fe222b1dd7fc8f329c1f5ec3da2cef3.jpg

This is gonna be painted so living a glue residue won't be an issue
4ec5d5e066ea6bd1b9ca3a51aafc2d65.jpg

If you're gonna have a varnished/stained window, you'll need to spend alot of time scraping/wiping away all traces of glue. It's boring, but unfortunately necessary !

Best to leave the frame overnight now for the glue to cure.
Once the glues dried you can start cleaning up the frame.

Chop of the horns (easiest to cut from both sides)

3d83fc540df8d1af0261191899c2e040.jpg


Then tidy up the corners for the draughtstrip. For years I just used a chisel
dc161923ac75c94e46c7e9d721ad2e67.jpg

But a multimaster type tool makes the job much quicker
9aa9db39c38cc017601f009d6442dcdd.jpg

a3794addaad951d796318ab5463b6364.jpg

Plane/smooth the inside and outside of the frame.
375fff2eb1f7b6e61df11e1ed77c7be4.jpg

Generally I'll just belt sand with 100 grit followed by orbital sanding 120 grit.
Finally just sand off ALL sharp edges with a piece of sandpaper.

By this point you should end up with a finished frame !! Have a beer or a brew to celebrate, relax and put your feet up!!

Next stage is making the sashes/casements ;)

Coley
 
Thanks Coley.

I've only done a couple of small windows, but I enjoyed the process, and that's a great guide you've posted.

I don't have a spindle, nor a tenoner, and at the time I did the first one, no p/t either, so the moulding was done on the router table. I know I could have morticed with the router too, but I bought a small chisel morticer, and I really like it for ease of setup, etc.

I've learned quite a bit from your guide, which I'll take into the next time :)
 
Thanks for taking the time and trouble to explain all this in detail.
I don't think I will ever need to make a window, but I do like to understand and appreciate how a professional joiner does.
 
WOW, amazing Coley, really interesting to learn how is done for this design.
Thanks loads.
 
Eric The Viking":2z7e1z2q said:
Thanks Coley.

I've only done a couple of small windows, but I enjoyed the process, and that's a great guide you've posted.

I don't have a spindle, nor a tenoner, and at the time I did the first one, no p/t either, so the moulding was done on the router table. I know I could have morticed with the router too, but I bought a small chisel morticer, and I really like it for ease of setup, etc.

I've learned quite a bit from your guide, which I'll take into the next time :)

Cheers Eric. That's really what I'm hoping to get across here. I'm fairly sure the exact window could be made with a few router cutters a hand tools. Forming the tenons can be done any number of ways, just for speed and ease a tenoners used.
I was dreading trying to explain how to mark the height of the jambs, cutting them by hand (drawing around the head and cill) is easier to do then setting up the tenoner- if only I could saw straight [SMILING FACE WITH OPEN MOUTH]
You did well to make it without a p/t. I guess it's taken for granted until it stops working.

Coley
 
AndyT":27u7t8jy said:
Thanks for taking the time and trouble to explain all this in detail.
I don't think I will ever need to make a window, but I do like to understand and appreciate how a professional joiner does.
My pleasure Andy. I'm not saying it's the right way or wrong way, but you should end up with a window that keep the wind and rain out ;) hopefully it won't fall to bits either lol

Coley
 
Thanks for the comments Custard and Peter.
I'll try and get the sash making bit up tonight.

I think trying to orientate the pics the right way may be a challenge. The only way I can think of,is to delete the tapatalk pics then upload them to photobucket. Im waiting to hear back from the tapatalk guys, an easy fix would be lovely.
Thanks guys

Coley
 
So the frames all done, now it's time to make the sashs. First thing is to machine the parts so they have rebates and a mould
d3bc886d369ab26abaf138147bf57988.jpg

The quickest way is to spindle them both at the same time
40fb509803efd2f2711cdc90e174cb4d.jpg

Another easy way would be a router table, obviously you would have to machine the mould and rebate seperstely.
The mould depth and the rebate depth are the same. This should make tenoning easy peasy cause the shoulders are square.
I've found the easiest way to check they are square/the same depth, is to machine the glazing bar first
ba1376f7fb2a7eb35c00d393679e5da7.jpg

This will show up any differences. Once you're happy, roller feed/feather boards and away you go.
4ad90e95d671ff1730e12ef17bfac916.jpg

6ce403d0d33db7959487dedb61df042f.jpg

Time to start marking out the parts for m &t's
b81fd7d3ab9ea62a3b8a061f079c9614.jpg


Coley
 
Back
Top