Search results

Can anybody clarify for me? I have the UK workshop app installed on my old Galaxy android phone. I have updated to a later Samsung S22 but can't find the app on Playstore. Any clues as to where I may find the app?

Has anyone got one of these machines? Looks very similar to the Jet JWP 12 thicknesser and I was wondering if it is worth considering as it is £100 cheaper for pretty much the same spec. I would appreciate any recommendations, and no, I don't need or want a planer/thicknesser, just a thicknesser.

Listing on behalf of a friend whose late father purchased, but didn't use this piece of equipment. The product is as new and as far as can tell has all parts but my friend doesn't know if her father actually set it up completely. The saw runs fine and has a light dusting of - dust! Current...

A friend is clearing her late father's workshop where he had a variety of tools and equipments, some unused. Among these is a Dewalt DW720 RAS and my friend seems to think her father bought but probably never used it and it has been sitting there gathering dust. The saw seems to be all there...

Probably been done to death but recommendations on reliable wood screws anyone, Torx or Pozi? Screwfix /Toolstation are convenient for me.

Still clearing. Had these clogging the workshop for a while and I'll never use them so free to whomsoever. Box dimensions 800 x 400 x 240 and 780 x 570 x 150 Good solid cases with saw stays. One is lockable, t'other has lock but no key but has latches. Collection from Salisbury.

Continuing the clear out, I have two Tormek jigs for woodturning tools and the toolsetter. Also included is the XB-100 base so the jigs can be used on a standard bench grinder. The base will require a support arm which can be the Tormek or the Record support arm which is cheaper, as are...

I have several methods of sharpening turning tools and have decided I don't need them all so I am selling off my Record wet system grinder if anybody is looking for one. Item is in little used, nearly new condition and still has almost two years left on the warranty. Wheel is 195mm dia. and...

Hi all I have for refurbishment a Bailey No 6 and it has a butchered cap iron and a Record lever cap. Has anyone got a Stanley lever cap and cap iron surplus to requirement that they wish to part company with?

Trying to do a clearout and came across a few bits. Anybody have a use for them? 1st pic is from I think an old Record power chuck set. 2nd pic is a couple of Nova chuck inserts. From looking at them one is 1" x 8TPI and the other is a 1" X 10TPI LH thread. Yours for cost of postage or...

I have - yet again - a bearing failure on my Charnwood BS350 bandsaw. I know they have used cheapo bearings 609z but unfortunately these are prone to seize and I want to replace them with decent 6092RS types. Unfortunately they have 2 bearings mounted on a threaded shaft on each side and I...

I hope I'm not opening a bag of worms here (as in sharpening advice😱) but can I call upon the wisdom of others here for advice on glue. I am putting together an oak rocking chair which will ultimately be used and stored in an unheated summerhouse with all associated temperature/moisture...

As a total newbie to buying hardwood timber, I had occasion to buy some European KD oak for a chair I plan to make. I collected the wood from a local sawmill but self select was not an option due to current regs. I didn't inspect closely but was assured this is prime oak, which I assume is QFA...

Hi all Anybody got an old Stanley 90 they wish to part with? I want to try my hand with one and I've seen a couple on fleabay but they are either stupid price or tatty.

Not sure which section to post this in, but can anyone point me in the direction of a supplier of an M33 x 3.5 thread ER32 collet chuck from the UK? (Not the Axi ER20 junior and not the Banggood from China version) I know I can get an MT2 version with drawbar but would prefer a direct thread...

Been making boxes lately ( a la Chas instructions - ta!) and Chas advised I post my own thread so here we go:-

Does anybody know whether this set has a removable centre point, and are they easy to hone? Also, at £74 for the set, is it value for the product offered?

Can I hurl this one at the combined knowledge of this forum? With the passing of a friend's father, I acquired a quantity of unidentified turning blanks going back to offcuts from the ark! I am stumped by this one below so any help welcomed. The blank is 150mm dia x 65mm deep. It weighs 508g...

Can anybody help? With the sad closure of Toolpost recently, on my wishlist was a Beall spindle tap M33 x 3.5 which they stocked. My question is, are there any other Beall stockists in the UK who may have said tool? Any help welcome?

I don't know if this is the right place but if anybody wants a manual for the Myford ML7 I have one to give away.