Search results

Hi Limey whats a weather bar? I only know so much in carpentry, Im more of a mechanical guy.

It turned out to be a the floor bolt mechanism connected to the door lock had uncoupled. A design floor from one of Howden most likely obsolete kit. I had to remove the bottom bolt as a temp fix until the customer sources the part or gets it fixed under warranty. Just for good measure I...

Hi Jsw, is there anywhere I can buy the glazing bars from? Getting out the router and searching for a suitable router bit sounds tedious to make a a Meyer or so of moulding. Hi James I checked the doors with the level and all seems good, however I can't check the hinges until I unbind the door...

If the threshold is at fault, for say water getting underneath and or unpainted, is there anything I can do without removing/replacing the cill?

Thanks Sgian Dubh, I hadn't thought of Checking the threshold. Now you mention it the varnish is a bit tired. How would it be fixed down? I would imagine a few coats of yacht varnish might help prevent the same happening again.....

Hi I need some advice on sorting out a stuck patio door. Only one of the patio doors the right one is stuck. Binding on the bottom opposite the hinge side. My thoughts were that the hinges had insufficient length screws, so working loose or hinges had bent or the wood had expanded on the...

Hi Bob, The motor does vibrate with the belt off, so could be a motor bearing issue as well. Did you build your 3 phase array yourself from separate vfd and motor or is this a dedicated kit?

Uploaded some video

Hi Jonnyb, could be that the bearing isnt correctly tightened. Im inclined to take the spindle and bearing out and refit if only to check any wear. It might mean I need a new rear roller bearing as I think it was a tight fit last time.

Hi Robbo I replaced the bronze bearing about a year or 2 ago and the belt. I havent used it much and it probably needs some levelling bot head to tailstock and across the bed bars. I did run the new bearing in for 1 hour on the lowest speed. There could be a couple of issues; 1) I found out...

Hi I purchased a used CL2 with a problamatic bearing or mis-alignment issue. I replaced the bronze bearing, back bearing and spindle which I thought made it run quieter and smoother although there was still some noise present. After recently attempting a bowl turn on a piece of 6" green ash...

Hi all been a while since last posting, I got hold of some vintage chisels and noticed that the edge had a slight curve in the grind from the left to right corner on some firmer chisels. Is this a feature or an anonmally due to poor sharpening technique from the previous owner? Jon

Hi Littleears, aside from getting to the route of your damp problem, I would recommend getting an Ozone generator. There about £30 from ebay or other online reatailers. If the machine is left on for a few hours with the door closed or preferably over night most of the airborn spores will be...

Thanks Fred Ive been meaning to take the cover off and investigate. However got one seized screw on top. I will have to get out the screw extractors. Hopefully an easy replacement such as an M6 screw. Meanwhile Im still in the process of fitting a new spindle and sealed bearing on my...

Recently acquired one of these 2nd hand. I fitted a standard fretsaw blad which will fit most hand fretsaws only for the blade to snap without apply a cut. Am I using the right length and style of blade or is there another reason? I did notice a lot of sideways travel / flex in the blade which...

Take a casting of the glued original in latex and cast one in resin, I think I have seen a few videos on Youtube especially from the restoration scene.

Im not sure about Rabbit control, however if you can get hold of Stoats or Pine Martins they are great predators of Grey Squirrels. Plus the native red squirrels are too fast or can travel out to the lighter branches and escape the Pine Martins and Stoats.

Hi Robbo, my Record Coronet 2 has a 4 ribbed belt. It is possible that this has been modified or later models had 5 ribbed pulleys / belts. However I did find a pdf manual for my lathe where the owner had written the code number for the hopefully correct specification. See below. I hope...

I recently bought a replacement spindle and bearing kit which Records tech guy assured me would fit my Blue Coronet2 only to discover that the supplied belt has one more rib than will fit my pulley. It has been suggested elsewhere to trim it to fit. However I would like my lathe to run as...

I am recently acquired a Record Power turbo visor model RPTV100-J minus charger and instruction manual. Sadly I cant get any info from Record as they have mislayed or possibly destroyed any copy of the instructions. I am hoping to get a charger if possible and a manual if anyone can point me...